25/04/2023 00:37:04

Heater - Radar (Remove and Replace)

Correction code 17201702 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the front fascia assembly. See Fascia Assembly - Front (Remove and Install).
  2. Disconnect the electrical harness from the BLE module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  3. Remove the screw that attaches the T badge support to the front fascia.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  4. Release the T badge support tabs from the front fascia, and then remove the T badge support from the front fascia.
  5. Release the locking tab, disconnect the radar heater connector, and then release harness from the clip.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  6. Release a corner of the adhesive on the radar heater, peel the radar heater away from the front fascia to remove, and then discard it.

Install

  1. Locate the scribe lines on the front fascia assembly for the radar heater installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    The scribe lines are located on the center of the front fascia assembly.
  2. Use IPA wipes to clean the installation area.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow 1 minute for dry time.
  3. Remove the adhesive backing on the LH side of new radar heater, align the bottom corner onto the scribe lines and adhere the bottom portion onto the front fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Alignment of the grid along scribe lines is key to radar operation.
  4. Remove the adhesive backing on the center of radar heater, align the bottom onto the scribe line, and then adhere the middle portion onto the front fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to not leave any creases or bubbles as the grid is adhered to the fascia.
  5. Remove the adhesive backing on the RH side of radar heater, align the bottom onto the scribe line, and then fully set both sides onto the front fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to not leave any creases or bubbles as the grid is adhered to fascia.
  6. Inspect the radar heater for bubbles and creases.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the radar heater is fully adhered onto the front fascia.
    Informational PurposesAn informational icon, calling your attention
    Note
    Maximum bubble diameter is 10mm.
  7. Secure the front fascia harness to the clip on the front fascia, connect the radar heater connector, and then secure the locking tab.
  8. Position the T badge support on the front fascia, and then install the clips and datums that attach the T badge support to the fascia.
  9. Install the screw that attaches the T badge support to the front fascia.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  10. Connect the electrical harness to the front BLE module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  11. Install the front fascia assembly. See Fascia Assembly - Front (Remove and Install).