22/05/2023 14:46:54

Compressor, Supermanifold, and A/C Lines (Remove and Replace)

Correction code 18204012 2.16 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Remove the A/C compressor. See A/C Compressor (Remove and Replace).
  2. Remove the NVH acoustic cover from the new AC compressor, and then remove any remaining adhesive material from the compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    The NVH acoustic cover must be fully removed to properly weigh the compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove as much adhesive material from the NVH acoustic cover as possible. Excessive material left on compressor will cause an inaccurate weight measurement.
    Tip: Use of the following tool(s) is recommended:
    • Flat scraper blade
    • Wire brush
  3. Remove the transportation plugs from the new A/C compressor.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
  4. Weigh the new A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    The new compressor should weigh 7193g. Escalate if the compressor weight is incorrect.
    Tip: Use of the following tool(s) is recommended:
    • Weighing scale - 1067799-00-A
  5. Install a new NVH blanket on the new A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Reuse the old NVH blanket if a new one is not available and the adhesive is in good working condition.
    1. Remove the new NVH blanket adhesive backing, and then lay the NVH acoustic cover down with the adhesive side facing upwards.
    2. Align the NVH acoustic cover cut outs to the suction port on the A/C compressor.
    3. Install the NVH acoustic cover around the suction port on the A/C compressor, and then continue to wrap the NVH cover around the compressor.
  6. Position the A/C compressor bracket on the compressor, and then install the bolts (x3) that attach the bracket to the compressor.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  7. Disconnect the A/C machine hoses from the A/C flush adapters.
    Tip: Use of the following tool(s) is recommended:
    • Heat pump flush kit - 1600279-00-A
    • Mastercool 2000 R134A A/C Machine - 1509224-00-A
  8. Remove the supermanifold to compressor A/C line. See A/C Line - Supermanifold to Compressor (Remove and Replace).
  9. Remove the supermanifold to HVAC A/C line. See A/C Line - Supermanifold to HVAC (Remove and Replace).
  10. Remove the supermanifold. See Supermanifold (Remove and Replace).