01/04/2024 14:04:18

Cover - Cushion - Driver Seat (Remove and Replace)

Correction code 13072202 1.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the driver seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
  2. With assistance, place the driver seat on a protected surface so that the underside of the seat can be accessed.
  3. Remove the screw that attaches the driver seat outboard side shield to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  4. Carefully release the clips (x7) that attach the driver seat outboard side shield to the seat assembly, but do not fully remove the side shield from the seat assembly.
  5. Disconnect the electrical harness from the seat switch.
  6. Remove the driver seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
  7. Release the seat back elastic straps (x2) from the driver seat frame.
  8. Release the soft trim retainers (x2) from the driver seat frame.
  9. Disconnect the FSC vent heat pad electrical connector from the driver seat controller.
  10. Release the clip and bracket that attach the FSC and FSB vent heat pad harnesses to the driver seat assembly, and then remove the harnesses from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    One harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them.
  11. Release the clip that attaches the driver seat harness to the seat frame bracket.
  12. Slide the OCS harness connector upward to release it from the SBR bracket, and then disconnect the electrical connector.
  13. Slide the SBR bracket upward to release it from the driver seat frame.
  14. Release the tabs (x2) to open the SBR bracket containing OCS harness, and then route the harness between the driver cushion and frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Routing the harness will avoid it getting snagged when the seat foam is removed from the seat frame.
  15. Release the soft trim retainer from the inboard side of the driver seat frame.
  16. Release the soft trim retainer from the outboard side of the driver seat frame.
  17. Release the soft trim retainer from front end of the driver seat frame.
  18. Position the seat assembly upright.
  19. Remove the driver seat seat cushion from the seat frame.
  20. Release the strap that attaches the driver seat cushion trim below the seat foam.
  21. Release the Velcro that attaches the driver seat cushion trim to the foam pad, and then fold the trim back until the first row of hog rings is exposed.
  22. Use diagonal cutters to cut and remove the front hog rings (x5) that attach the driver seat cushion trim cover to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on the foam as necessary to allow additional access to the rings.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Verify any excess pieces have been removed from the foam.
  23. Release the remaining Velcro that attaches the driver seat cushion trim to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the trim back until access to OCS is clear.
  24. Use diagonal cutters to cut and remove the center hog rings (x2) that attach the driver seat cushion trim to the foam pad.
  25. Use diagonal cutters to cut and remove the rear hog rings (x3) that attach the driver seat cushion trim to the foam pad.
  26. Remove the driver seat cushion trim from the foam pad.

Install

  1. Position the driver seat seat cushion trim onto the foam pad for hog ring installation.
  2. Install the hog rings (x3) that attach the rear of the driver seat cushion trim to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place the hog ring into the pliers prior to installation. Start with center ring and work outward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on the foam to allow additional access if necessary.
    Tip: Use of the following tool(s) is recommended:
    • Hog ring pliers (1501599-00-A)
  3. Install the hog rings (x2) that attach the center of the driver seat cushion trim to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place the hog ring into the pliers prior to installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on the foam to allow for additional access if necessary.
    Tip: Use of the following tool(s) is recommended:
    • Hog ring pliers (1501599-00-A)
  4. Secure the Velcro to the driver seat cushion foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure up to the section where front hog rings will be installed.
  5. Install the hog rings (x5) that attach the front of the driver seat cushion trim to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place the hog ring into the pliers prior to installation. Start with center ring and work outward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down on the foam to allow for additional access if necessary.
    Tip: Use of the following tool(s) is recommended:
    • Hog ring pliers (1501599-00-A)
  6. Secure the remaining portion of the Velcro that attaches the driver seat cushion trim to the foam pad.
    Informational PurposesAn informational icon, calling your attention
    Note
    Wrap the remaining portion of the trim over the foam pad.
  7. Secure the strap that attaches the driver seat cushion trim below the seat foam.
  8. Position the driver seat cushion assembly onto the seat assembly, and then feed the cushion trim between the seat back trim and seat frame to install cushion assembly to the seat frame.
  9. Position the driver seat assembly onto the seat back.
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect the seat from damage.
  10. Secure the soft trim retainer onto the front end of seat frame.
  11. Secure the soft trim retainer on the outboard side of the seat frame.
  12. Secure the soft trim retainer on the inboard side of the seat frame.
  13. Install the OCS harness into the SBR bracket, and then secure the tabs (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the tabs are fully engaged.
  14. Slide the SBR bracket downward to install it onto the seat frame bracket.
  15. Connect the OCS harness electrical connector, and then install the connector onto the SBR bracket.
  16. Fasten the clip that attaches the driver seat harness to the seat frame bracket.
  17. Secure the clip and bracket that attach the FSC and FSB vent head pad harnesses to the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    One harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them.
  18. Connect the FSC vent heat pad electrical connector to the driver seat controller.
  19. Install the soft trim retainers (x2) to the seat frame.
  20. Secure the seat back elastic straps (x2) to the seat frame.
  21. Position the seat assembly upright.
  22. Install the driver seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
  23. Connect the electrical harness to the back rest and cushion adjust switch assembly, and then verify the functions of the seat switches.
  24. Position the driver seat outboard side shield onto the seat, and then install the clips (x7) that attach the side shield to the seat.
    Tip: Apply pressure to the side shield to fully seat the clips. The side shield should sit flush against the seat cushion.
  25. Install the screw that attaches the driver seat outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  26. Install the driver seat into the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
  27. Connect a laptop with Toolbox 3 to the vehicle.
  28. Click the Actions/Autodiag tab, and then type "Calibration" in the search field.
  29. Click PROC_VCSEATD_SEAT-CALIBRATESearch for routine in ToolboxVCSEAT Driver Seat Calibration, and then click Run and allow routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify there are no items on seat during this routine. Click the "X" at top right of window to close once complete.
  30. Disconnect Toolbox 3 and remove the laptop from the vehicle.
  31. Move the driver seat to the original position.
  32. Raise the LH windows and close the LH front door.