17/06/2022 13:31:38

Actuator - Duct - Footwell - RH (Remove and Replace)

Correction code 18108712 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Move the front passenger seat fully rearwards.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect LV power. See LV Power (Disconnect and Connect).
  4. Remove the front passenger footwell cover. Cover - Footwell - Passenger (Remove and Replace).
  5. Remove and discard the patch bolts (x2) that attach the front passenger knee airbag assembly to the instrument panel.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • External Torx E10
    • ¼ in to 3/8 in adapter
  6. Release the tabs (x6) that attach the front passenger knee airbag assembly to the instrument panel, and then partially lower the airbag.
    Informational PurposesAn informational icon, calling your attention
    Note
    The front passenger knee airbag is still connected to the vehicle. Be careful not to damage the electrical connectors when lowering the airbag from the instrument panel.
  7. Disconnect the electrical connectors (x2) from the front passenger knee airbag assembly, and then set the assembly aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    The front passenger knee airbag has 2 locking tabs.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  8. Remove the screws (x2) that attach the RH footwell duct actuator to the vehicle, and then release the actuator from the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of the direction of the keyed socket.
    Tip: Use of the following tool(s) is recommended:
    • T20 bit
  9. Disconnect the electrical connector, and then remove the RH footwell duct actuator from the vehicle.

Install

  1. Position the RH footwell duct actuator into the vehicle, and then connect the electrical connector.
  2. Install the screws (x2) that attach the RH footwell duct actuator to the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Note the keyed socket angle upon installation matches the actuator.
    Tip: Use of the following tool(s) is recommended:
    • T20 bit
  3. While supporting the front passenger knee airbag assembly, connect the electrical connectors (x2).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully connect the airbag electrical connector to prevent damage to the electrical connectors.
  4. Hook the tabs (x6) before putting the front passenger knee airbag onto the instrument panel, and then seat the airbag to the instrument panel.
  5. Install the new patch bolts (x2) that attach the front passenger knee airbag to the instrument panel.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • External Torx E10
    • ¼ in to 3/8 in adapter
  6. Install the front passenger footwell cover. Cover - Footwell - Passenger (Remove and Replace).
  7. Connect LV power. See LV Power (Disconnect and Connect).
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Return the front passenger seat to its original position.