01/04/2024 14:02:51

Module - Bluetooth Low Energy (BLE) - Front (Remove and Replace)

Correction code 17451112 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-02-06: Changed Service Redeploy to Service CAN Redeploy.

Remove

  1. Remove the front fascia assembly. See Fascia Assembly - Front (Remove and Install).
  2. Disconnect the electrical harness from the BLE module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  3. Remove the screw that attaches the T badge support to the front fascia.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  4. Release the T badge support tabs from the front fascia, and then remove the T badge support from the front fascia.
  5. Remove the screws that attach the T badge to the T badge support.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench

Install

  1. Position the front BLE module on the T badge support, and then install the two screws that attach the module to the T badge support.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  2. Position the T badge support on the front fascia, and then install the clips and datums that attach the T badge support to the fascia.
  3. Install the screw that attaches the T badge support to the front fascia.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  4. Connect the electrical harness to the front BLE module.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  5. Install the front fascia assembly. See Fascia Assembly - Front (Remove and Install).
  6. Connect a laptop with Toolbox to the vehicle.
  7. In Toolbox, click the Actions/Autodiag tab, and then search for "Redeploy".
  8. Click UPDATE_CAN-REDEPLOYSearch for routine in ToolboxService CAN Redeployhv / Drive Inverter DIRE1L Replacement - CAN Redeployhv / Drive Inverter DIRE1R Replacement - CAN Redeployhv / Drive Inverter DIRE2 Replacement - CAN Redeployhv / Front Drive Inverter Replacement - CAN Redeployhv / Rear Drive Inverter Replacement - CAN Redeployhv / Rear Left Drive Inverter Replacement - CAN Redeployhv / Rear Right Drive Inverter Replacement - CAN Redeployhv / Front Drive Unit Replacement - CAN Redeployhv / Rear Drive Unit Replacement - CAN Redeploy, and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Select "X" at top right of window to close once complete. The routine will state pass but the update will continue to run in the background. The UI will show update progress.
  9. In Toolbox, click the Actions/Autodiag tab, and then search for "Endpoint".
  10. Click TEST-SELF_VCSEC_X_ENDPOINT-COMMSearch for routine in ToolboxBLE Endpoint Communication Check, and then click Run Network and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right of the window to close once complete.
  11. Disconnect Toolbox and remove the laptop from the vehicle.
  12. Raise the LH front window and close the LH front door.