19/10/2022 10:29:10

Duct - Instrument Panel - Front Passenger (Remove and Replace)

Correction code 18108102 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the RH front door.
  2. Lower the RH front window.
  3. Move the RH front seat rearwards.
  4. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  5. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  6. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. On the vehicle touchscreen, touch CONTROLS (vehicle icon) > GLOVE BOX to open the glove box.
  8. Disconnect LV power. See LV Power (Disconnect and Connect).
  9. Remove the center console phone dock. See Phone Dock - Center Console (Remove and Replace).
  10. Remove the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  11. Remove the touchscreen. See Touchscreen (HW3) (Remove and Replace).
  12. Release the tabs (x4) that attach the instrument panel closeout panel to the instrument panel, and then remove the closeout panel from the vehicle.
  13. Remove the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  14. Remove the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  15. Remove the front passenger knee airbag. See Knee Airbag - Front Passenger (Remove and Replace).
  16. Remove the glove box. See Glove Box (Remove and Replace).
  17. Disconnect the front passenger instrument panel duct sensor connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the connector. Do not damage components.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  18. Release the rivets (x2) that attach the front passenger instrument panel duct to the instrument panel, and then remove the duct from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool

Install

  1. Position the front passenger instrument panel duct on the vehicle, and then install the rivets (x2) that attach the duct to the instrument panel.
  2. Connect the front passenger instrument panel duct sensor connector.
  3. Install the glove box. See Glove Box (Remove and Replace).
  4. Install the front passenger knee airbag. See Knee Airbag - Front Passenger (Remove and Replace).
  5. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  6. Install the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  7. Position the instrument panel closeout panel on the vehicle, and then install the tabs (x4) that attach the closeout panel to the instrument panel.
  8. Install the touchscreen. See Touchscreen (HW3) (Remove and Replace).
  9. Install the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  10. Install the center console phone dock. See Phone Dock - Center Console (Remove and Replace).
  11. Connect LV power. See LV Power (Disconnect and Connect).
  12. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  13. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  14. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  15. Move the RH front seat to original position.
  16. Raise the RH front window.
  17. Close the RH front door.