17/06/2022 13:02:22

Valance - Front Fascia (Remove and Replace)

Correction code 10012202 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Valance - Front Fascia (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the valance to the front aero shield
6 Nm (4.4 lbs-ft)
  • 10 mm socket
  • 4 in extension
  • Flex head ratchet/flex head torque wrench
 Reuse Install with Loctite 222
Nut that attaches the valance to the wheelhouse liner
3 Nm (2.2 lbs-ft)
  • 10 mm deep socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Raise the vehicle Raise Vehicle - 2 Post Lift.
  3. Remove the bolts and clips that attach the front fascia valance to the front aero shield.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  4. Release the three clips that attach the LH wheelhouse liner to the valance and front fascia.
  5. Release the three clips that attach the RH wheelhouse liner to the valance and front fascia.
  6. Release the electrical harness from the top of the front fascia valance, and then disconnect the electrical harness from the pedestrian warning speaker.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  7. Release the eight clips that attach the valance to the front fascia.
  8. Remove the two nuts that attach the valance to the front fascia near the wheelhouse liners, and then remove the valance from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Ratchet/torque wrench

Install

  1. With an assistant, position the valance on the front fascia, and then install the two nuts that attach the valance to the LH and RH wheelhouse liners.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Ratchet/torque wrench
  2. Install the clips that attach the valance to the front fascia assembly.
  3. Connect the electrical harness to the pedestrian warning speaker, and then clip the harness into the valance.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  4. Install the three clips that attach the RH wheelhouse liner to the valance and front fascia.
  5. Install the three clips that attach LH wheelhouse liner to the valance and front fascia.
  6. Position the two valance datums into the front aero shield.
  7. Apply Loctite 222 to the three bolts, and then install the bolts and clips that attach the valance to the front aero shield.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
  8. Lower the vehicle Raise Vehicle - 2 Post Lift.
  9. Raise the LH front window and close the LH front door.