10/08/2023 11:23:39

Harness - 2nd Row Seat - RH (Remove and Replace)

Correction code 17100082 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-08-10: Cleaned up procedure.

Remove

  1. Open the RH doors and lower the RH windows.
  2. Move the front passenger seat forward.
  3. Remove the RH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  4. Fold the RH 2nd row seat back to the down position.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the seat cushion is not present, protect the seat as required.
  5. Disconnect the RH 2nd row seat back harness electrical connector.
  6. Release the clip that attaches the RH 2nd row seat back harness to the pivot bracket.
  7. Remove the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  8. Release the clips (x2) that attach the RH 2nd row back side cover to the seat back assembly, and then remove the cover from the assembly.
  9. Remove the clip that attaches the RH 2nd row shoulder plastic trim to the latch assembly.
  10. Remove the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  11. Lift the RH 2nd row headrest LH guide lock locking tab, and then slide the guide lock out of the seat frame assembly. Repeat this step for the RH 2nd row headrest RH guide lock.
  12. Remove the bolts (x2) that attach the RH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Fold the RH 2nd row seat back to the vertical position, but do not latch the seat back.
  14. Release the clips (x8), disconnect the backrest harness electrical connector, and then remove the RH 2nd row backrest cushion from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the upper clips first to disconnect backrest the connector.
  15. Remove the clips (x3) that attach the RH 2nd row shoulder trim to the back frame.
  16. Release the clips (x6) that attach the RH 2nd row seat shoulder trim to the seat back assembly, disconnect the electrical connector, and then remove the shoulder trim from the assembly.
  17. Disconnect the RH 2nd row seat latch electrical connector.
  18. Release the clips (x4) that attach the RH 2nd row seat harness to the seat back assembly, and then remove the harness from the assembly.

Install

  1. Position the RH 2nd row seat back harness onto the RH 2nd row seat back assembly, and then install the clips (x4) that attach the harness to the seat back.
  2. Connect the RH 2nd row seat latch electrical connector.
  3. Position the RH 2nd row seat shoulder trim onto the RH 2nd row seat back assembly, connect the electrical connector, and then fasten the clips (x6) that attach the shoulder trim to the seat back.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the fold switch with the frame gap to avoid damage.
  4. Install the clips (x3) that attach the RH 2nd row shoulder trim to the back frame.
  5. Position the RH 2nd row backrest cushion onto the RH 2nd row backrest, connect the backrest harness electrical connector, and then secure the clips (x8) that attach the cushion to the backrest.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the lower clips first, then connect backrest harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure all clips are properly seated.
  6. Fold the RH 2nd row seat back to the down position.
  7. Install the bolts (x2) that attach the RH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Slide the RH 2nd row headrest LH guide lock into RH 2nd row backrest frame to install it into the back rest. Repeat this step for the RH 2nd row headrest RH guide lock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the headrest guide locking tabs are fully engage.
    Informational PurposesAn informational icon, calling your attention
    Note
    The headrest guide lock with the adjustment button is installed inboard.
  9. Install the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  10. Install the clip that attaches the RH 2nd row shoulder trim to the latch assembly.
  11. Position the RH 2nd row back side cover onto the seat back assembly, and then secure the clips (x2) that attach the cover to the assembly.
  12. Install the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  13. Install the clip that attaches the RH 2nd row seat back harness to the pivot bracket.
  14. Connect the RH 2nd row seat back harness electrical connector.
  15. Fold the RH 2nd row seat to the up position.
  16. Install the RH 2nd row seat side bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  17. Move the front passenger seat to its original position.
  18. Raise RH windows and close the RH doors.