2025-10-01

Inductive Charger - Center Console (Remove and Replace)

Correction code 15193902 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2025-10-01: Added link to Service CAN Redeploy routine.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Release the clips (x4) that attach the phone dock to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull up at the bottom of the phone dock and swing out from under the center console.
  3. Release the clip, then disconnect the electrical connectors (x3). Remove the phone dock from the instrument panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Release the connector locks before pulling straight out of each socket to avoid damage.
  4. Remove the screws (x3) that attach the inductive charger to the phone dock.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  5. Release the tabs (x2) at the top of the phone dock, then remove the inductive charger from the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Angle the inductive charger up and slide out of the phone dock.

Install

  1. Fasten the tabs (x2) that attach the inductive charger into the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the inductive charger datums into the phone dock, and then fully engage the tabs at the top of the phone dock.
  2. Install the screws (x3) that attach the inductive charger to the phone dock.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  3. Secure the clip that attaches the phone dock electrical harness, then connect the electrical connectors (x3).
  4. Fasten the tabs (x4) that attach the phone dock to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the datums forward into the center console, then secure the tabs down.
  5. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  6. Run UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    • Thermal ➜ HVAC ➜ CAN Redeploy
    • chassis ➜ DPB Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Post Replacement ➜ CAN Redeploy
    • chassis ➜ IDB Post Replacement ➜ CAN Redeploy
    • chassis ➜ RCU Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
    • chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
    .
  7. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  8. Raise the LH front window and close the LH front door.