15/09/2022 11:13:19

Coat Hook - Rear - LH (Remove and Replace)

Correction code 15204302 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the driver seat fully forward.
  3. Open the LH rear door.
  4. Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  5. Push open the LH rear coat hook.
  6. Pry open to release the tabs (x2) that attach the rear coat hook screw cover.
  7. Remove the rear coat hook screw.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 bit
  8. Open the liftgate.
  9. Remove the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  10. Fold down the LH rear seat.
  11. Remove the LH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  12. Release the clips (x4) that attach the LH lower C-pillar trim to the mid C-pillar trim.
  13. Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  14. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  15. Remove the bolt that attaches the LH rear corner of the headliner to the body.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  16. Release the clips (x7) that attach the LH rear corner of the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Headliner is being supported by tethers along roof rail. Push upward and inward to release the hook on the coat hook assembly from the body.
  17. Release the coat hook tether clip from the body.
  18. Release the tabs (x4) that attach the coat hook bezel to the headliner.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry the tab from the top front corner first for best results.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use non-marring tool to prevent damage to the headliner.
  19. Disconnect the electrical connector to the rear coat hook.
  20. Remove the bolts (x4) that attach the rear coat hook to the headliner, and then remove the coat hook from the vehicle.
    1.2 Nm (.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit

Install

  1. Install the bolts (x4) that attach the rear coat hook to the headliner as follows:
    1.2 Nm (.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
    1. Install the upper tether using the top rear bolt first.
    2. Fold the tether strap to align the lower holes, and then install the lower rear bolt.
      Informational PurposesAn informational icon, calling your attention
      Note
      Make sure the tether is not twisted.
    3. Install the remaining bolts (x2).
  2. Connect the rear coat hook electrical connector.
  3. Secure the tabs (x4) that attach the coat hook bezel to the headliner.
  4. Secure the clips (x9) that attach the LH rear corner of the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the rear coat hook upward and outward to secure the hooks to the body flange at the top of the coat hook assembly.
  5. Install the bolt that attaches the rear corner of the headliner to the body.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  7. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  8. Secure the clips (x4) that attach the LH lower C-pillar trim to the mid C-pillar trim.
  9. Install the LH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  10. Put the LH rear seat in the upright position .
  11. Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  12. Close the liftgate.
  13. Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  14. Close the LH rear door.
  15. Move the driver seat back to its original position.
  16. Raise the LH front window and close the LH front door.