2026-08-09

Panel - Door Trim - Front - LH (Remove and Replace)

Correction code 15130202 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-04-11: Added links to armrest service cover and door trim reflector.

Remove

  1. Remove the LH front door trim decor. See Decor - Trim - Front Door - LH (Remove and Replace).
  2. Remove the LH front door trim reflector. See Reflector - Door Trim - Front - LH (Remove and Replace).
  3. Remove the LH front door armrest service cover. See Cover - Service - Armrest - Front Door - LH (Remove and Replace).
  4. Remove the bolts (x4) that attach the LH front door trim panel to the door assembly.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • T30 socket
  5. Release the clips (x8) that attach the LH front door trim panel to the door assembly, then release the handle cable, then release the connector lock and disconnect the electrical connector, and then remove the panel from the door.
  6. Remove any left over clip retainers from the LH front door assembly.
    Note
    The number of retainers will vary with each removal.

Install

  1. Position the LH front door trim panel onto the door assembly, secure the handle cable, connect the electrical connector and engage the connector lock, and then fasten the clips (x8) that attach the panel to the assembly.
    Note
    Secure any retainers.
    Note
    Replace any broken clips.
  2. Install the bolts (x4) that attach the LH front door trim panel to the door assembly.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • T30 socket
  3. Install the LH front door armrest service cover. See Cover - Service - Armrest - Front Door - LH (Remove and Replace).
  4. Install the LH front door trim reflector. See Reflector - Door Trim - Front - LH (Remove and Replace).
  5. Install the LH front door decor temporarily. See Decor - Trim - Front Door - LH (Remove and Replace).
    Note
    The trim decor will be removed again later in this procedure.
  6. Enable Service Mode. See Service Mode (Enable and Disable).
  7. Reinstall vehicle firmware through the touchscreen as follows:
    1. Touch Controls > Service Mode > Software Reinstall and then touch Request.
      Note
      Click X at the top left of the window to close once confirmed.
    2. Touch the clock on the top center of the touchscreen, or touch the Software > SOFTWARE UPDATE, and then touch INSTALL NOW to start the firmware reinstallation.
      Note
      Check the touchscreen and ensure that the firmware package is installing.
    3. Once the firmware reinstall is completed, verify on the touchscreen that the "Release Notes" are present.
      Note
      If the vehicle firmware reinstallation failed, an error message will be displayed.
  8. Close the LH front door.
  9. Check the gap fitment of the LH front door decor to the IP decor.
    Note
  10. Adjust the LH front door trim:
    6 Nm (4.4 lbs-ft)
    Note
    Loosen the screw, and then rotate the adjustment nut until the desired specification is reached. Tighten the screw once complete
    Tip
    Use of the following tool(s) is recommended:
    • Torx T30 socket
    • 18 mm deep socket
  11. Install the LH front door trim decor. See Decor - Trim - Front Door - LH (Remove and Replace).
  12. Check the gap fitment of the LH front door decor to the IP decor.
    Note