03/10/2024 13:10:50

Ride Height (Adjust)

Correction code 31001000 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-12-04: Revised procedure to be in line with latest PDS validation.
Informational PurposesAn informational icon, calling your attention
Note
This procedure assumes the vehicle suspension is operating as intended. If needed, a vehicle general inspection can be performed.

Procedure

  1. At the alignment rack, verify that the turn and slip plates are locked.
  2. Align the vehicle to the alignment rack ramps, drive the vehicle onto the alignment rack, and then shift into Park.
  3. Set vehicle ride height to "Medium": on the touchscreen, touch Controls > Suspension > Medium.
  4. Open the LH front door and lower the window.
  5. On the touchscreen, touch Controls > Service > Wheel Configuration and confirm that the wheel configuration is set correctly.
  6. Set the steering wheel/yoke straight ahead.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the steering wheel/yoke bubble level to confirm that the front wheels are pointing straight forward.
  7. With the LH front door open, manually latch the LH front door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not close the door with the latch engaged.
  8. Put wheel chocks at both sides of the LH rear wheel.
  9. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  10. Raise the alignment rack to a comfortable working height.
  11. Install inflation hoses onto all four wheels so that tire pressures can be set automatically.
  12. Set the tire machine pressures to match those specified for the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to the "Tire and Loading Information" label located on the driver side B-pillar.
  13. Verify that the chassis height measurement tool (1071271-00-A) is zeroed at 51 mm, and adjust if necessary.
  14. Remove the inflation hoses from all four wheels, and then reinstall the valve stem caps.
  15. In Toolbox 3, select the Actions tab and search for "Level Tesla Air Suspension", select PROC_TAS_X_LEVEL-TO-HEIGHTSearch for routine in ToolboxLevel Tesla Air SuspensionChassis / Alignment & Tires - Set Suspension Height, select Cycle, and click Run.
  16. Perform air suspension calibration: in Toolbox 3, select the Actions tab and search for "Calibrate Air Suspension", and then select PROC_TAS_X_CALIBRATE-RIDE-HEIGHTSearch for routine in ToolboxTesla Ride Height Calibration.
  17. Measure the vehicle ride height at the 4 designated points, enter the measured ride height values into Toolbox, and then click Run.
  18. In Toolbox 3, select the Actions tab and search for "Level Tesla Air Suspension", select PROC_TAS_X_LEVEL-TO-HEIGHTSearch for routine in ToolboxLevel Tesla Air SuspensionChassis / Alignment & Tires - Set Suspension Height, select Cycle, and click Run.
  19. Check the ride height calibration: in Toolbox 3, select the Actions tab and search for "Check Tesla Ride Height Calibration", and select PROC_TAS_X_CHECK-RIDE-HEIGHT-CALIBRATIONSearch for routine in ToolboxCheck Tesla Ride Height Calibration.
  20. Measure the vehicle ride height at the 4 designated points, enter the measured ride height values into Toolbox, and then click Run.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the routine fails, perform air suspension calibration through Toolbox 3. If calibration fails, find the root cause before continuing this procedure.
  21. Fully lower the alignment rack.
  22. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  23. Pull the door handle to release the LH front door latch.
  24. Remove the steering wheel/yoke bubble level.
  25. Remove the wheel chocks from the LH rear wheel.
  26. Remove the vehicle from the alignment rack.