2023-01-25

Molding - Rocker Panel - LH (Remove and Replace)

Correction code 12202002 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Torque Specifications

Table 1. Torque Specifications: Molding - Rocker Panel - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH fairing to the body
3 Nm (2.2 lbs-ft)
  • Ratchet/torque wrench
  • 4 in extension
  • 8 mm socket
 Reuse
Upper bolts (x7) and lower bolts (x4) that attach the LH rocker panel molding to body
3 Nm (2.2 lbs-ft)
  • Ratchet/torque wrench
  • 4 in extension
  • 10 mm socket
 Reuse

Remove

  1. Open the LH front and rear doors.
  2. Remove the rocker panel scuff plate. See Scuff Plate - Rocker Panel - LH (Remove and Replace).
  3. Remove the push clip that attaches the rocker panel molding to the LH front wheel arch liner.
  4. Remove the push clips (x2) that attach the rocker panel molding to the LH rear wheel arch liner.
  5. Remove the bolts (x2) that attach the LH fairing, and then release the tabs (x4) that attach the fairing to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
  6. Release the bolt covers (x3) on the bottom edge of the LH rocker panel molding.
  7. Remove the upper bolts (x7) and lower bolts (x4) that attach the LH rocker panel molding to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
  8. Release the LH rocker panel molding at the front and rear fenders first, and then remove the molding from the vehicle.

Install

  1. Install the LH rocker panel molding on the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the rocker panel molding at the front and rear fenders.
    Informational PurposesAn informational icon, calling your attention
    Note
    Insert the rocker panel molding above the jack pads.
  2. Install the upper bolts (x7) and lower bolts (x4) that attach the LH rocker panel molding to body.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
  3. Secure the covers (x3) on the bottom edge of the LH rocker panel molding.
  4. Secure the tabs (x5) that attach the LH rear wheel fairing to the body.
  5. Install the bolts (x2) that attach the LH rear wheel fairing to the body.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
  6. Install the push clips (x2) that attach the rocker panel molding to the LH rear wheel arch liner.
  7. Install the push clip that attaches the rocker panel molding to the LH front wheel arch liner.
  8. Install the rocker panel scuff plate. See Scuff Plate - Rocker Panel - LH (Remove and Replace).