05/02/2024 01:07:43

Side Repeater - Front - LH (HW4) (Remove and Replace)

Correction code 17403702 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-02-05: Added a caution to wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Apply masking tape to the LH front fender assembly at the edges of the LH front side repeater.
    Tip: Use of the following tool(s) is recommended:
    • Masking tape
  2. Release the push clip that attaches the LH front side repeater to the LH front fender assembly.
    Figure 1. Inside fender view is for clarity only and access is not required for procedure
    1. Apply light constant pressure towards the fender at the rear of the side repeater, and keep pressure applied until the side repeater is released from the fender.
    2. Slide the side repeater approximately 5 mm towards the rear of the vehicle until the front clip is clear of the fender.
    3. Pull the front end of the side repeater away from the fender until the front clip releases from the fender.
    4. Slide the side repeater towards the front of the vehicle until the rear hook clip releases from the fender.
  3. Disconnect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Press down on the lock release and pull the connector away from the side repeater camera. Release the red locking tab and press down to disconnect the side repeater connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
    Tip: Use of the following tool(s) is recommended:
    • Pocket screwdriver
  4. Remove the LH front side repeater from the vehicle.
  5. Remove the LH front side repeater camera. See Side Repeater Camera - Front - LH (HW4) (Remove and Replace).

Install

  1. Install the LH front side repeater camera. See Side Repeater Camera - Front - LH (HW4) (Remove and Replace).
  2. Connect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the tape first, if present.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the side repeater connectors, and then engage the red locking tab on the side repeater connector.
  3. Open the LH front door.
  4. Reset the Driver Assistance System (DAS).
    1. Unlock the vehicle gateway. See Gateway (Unlock).
    2. On the touchscreen Service Mode menu, touch Driver Assist > Cameras > Reset DAS.
    3. On the touchscreen Cameras diagram, confirm that the Reset DAS button is highlighted green and that all DAS components display a green status light.
      Informational PurposesAn informational icon, calling your attention
      Note
      Investigate and rectify any DAS components that display a red status light.
  5. Close the LH front door.
  6. Install the push clip that attaches the LH front side repeater to the LH front fender assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure all tabs are intact and installed in place correctly.
    1. Insert the side repeater rear hook clip into the repeater slot in the fender, apply light constant pressure at the rear of the repeater, and then keep pressure until the repeater is installed.
    2. Slide the side repeater rearwards until the rear hook clip engages the fender and the front clip clears the edge of the repeater slot in the fender.
    3. Press on the front of the side repeater until the front clip is inside of the repeater slot and keep pressure on the front and rear of the repeater until installation is complete.
    4. Slide the side repeater towards the front of the vehicle until the front clip engages the fender, and then release pressure on the repeater.
  7. Remove the masking tape from the LH front fender assembly at the edges of the LH front side repeater.