04/06/2024 18:02:30

Mount - Bushing Carrier - Front Drive Unit - RH (Remove and Replace)

Correction code 39012402 6.65 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-08-02: Added steps to disconnect frunk harness from front drive unit connector and remove ground strap.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Move the vehicle to a 2 post lift. See Raise Vehicle - 2 Post Lift.
  2. Perform a cooling system thermal fill drain. See Thermal Fluid - Cooling System (Fill/Drain).
  3. Remove the LH and RH rocker panel scuff plates. See Scuff Plate - Rocker Panel - LH (Remove and Replace).
  4. Remove the LH and RH rocker panel moldings. See Molding - Rocker Panel - LH (Remove and Replace).
  5. Position the 2 post lift pads for HV battery removal.
  6. Set the steering wheel straight ahead, place a protector sheet onto the driver seat, and then install the steering wheel lock.
  7. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Disconnect LV power. See LV Power (Disconnect and Connect).
  9. Set the high voltage multimeter to DC voltage, lightly touch the probes to the auxiliary battery connector contacts, and verify that the multimeter displays a voltage.
    Informational PurposesAn informational icon, calling your attention
    Note
    Battery voltage is typically 14.5 to 15.5 volts.
  10. Remove the bolt that attaches the ground strap to the front drive unit.
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is captive to the ground strap.
  11. Pull the red tab, and then pull the tab again to disconnect the frunk harness from the front drive unit harness connector.
  12. Release the clip that attaches the frunk harness to the front drive unit.
  13. Loosen the LH and RH front axle nuts.
  14. Remove the LH and RH front wheels. See Wheel Assembly (Remove and Install).
  15. Remove the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
  16. Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
  17. Remove the leather glove protectors and the HV insulating gloves.
  18. Remove the LH and RH 2nd row seat side bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  19. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  20. Remove the DC input HV header foam block.
  21. Remove the bolt that secures the charge port busbar connector access door.
  22. Remove the bolts (x2) that attach the charge port busbar connector to the DC input HV header.
    9 Nm (6.6 lbs-ft)
  23. Lift the charge port busbar connector to remove the connector from the DC input HV header.
  24. Remove the LH and RH shear plates. See Shear Plate - Rear Subframe - LH (Remove and Replace).
  25. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  26. Remove the front skid plate. See Skidplate - Front (Remove and Replace).
  27. Remove the HV Battery. See HV Battery (AWD) (Remove and Install).
  28. Remove the front fascia valance. See Valance - Front Fascia (Remove and Replace).
  29. Remove the front subframe. See Subframe Assembly - Front (Remove and Install).
  30. Remove the LH and RH front halfshafts. See Halfshaft - Front Drive Unit - LH (Remove and Replace) and Halfshaft - Front Drive Unit - RH (Remove and Replace).
  31. Remove the front drive unit from the vehicle. See Drive Unit - Front (Remove and Install).
  32. With the help of an assistant, verify that the front drive unit is securely strapped to the transmission jack fixture, remove the bolts (x4) that attach the RH side bushing carrier to the drive unit, and then remove the busing carrier from the drive unit.

Install

  1. With the help of an assistant, install the RH side bushing carrier to the front drive unit, install and hand tighten the bolts (x4) that attach the bushing carrier to the drive unit, then tighten the bolts in the sequence shown.
    60 Nm (44.2 lbs-ft) +50 deg
  2. Install the front drive unit into the vehicle. See Drive Unit - Front (Remove and Install).
  3. Install the LH and RH front halfshafts. See Halfshaft - Front Drive Unit - LH (Remove and Replace) and Halfshaft - Front Drive Unit - RH (Remove and Replace).
  4. Install the front subframe. See Subframe Assembly - Front (Remove and Install).
  5. Install the front fascia valance. See Valance - Front Fascia (Remove and Replace).
  6. Install the HV Battery. See HV Battery (AWD) (Remove and Install).
  7. Install the front skid plate. See Skidplate - Front (Remove and Replace).
  8. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  9. Install the LH and RH shear plates. See Shear Plate - Rear Subframe - LH (Remove and Replace).
  10. Install the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
  11. Install the LH and RH front wheels. See Wheel Assembly (Remove and Install).
  12. Use an alcohol wipe to clean the charge port busbar connector lead contact surfaces of residual Penetrox, and allow at least one minute to dry.
  13. Use an alcohol wipe to clean the DC input HV header terminal contact surfaces of residual Penetrox, and allow at least one minute to dry.
  14. Apply two small drops of Penetrox onto each DC input HV header terminal contact surface, and spread evenly.
  15. Install the charge port busbar connector onto the DC input HV header, and then install the bolts (x2) that attach the connector to the header.
    9 Nm (6.6 lbs-ft)
  16. Put on the HV insulating gloves and leather over gloves.
  17. Use the Hioki resistance meter to measure the resistance between the charge port busbar connector lead and the DC input HV header bolt head.
    Informational PurposesAn informational icon, calling your attention
    Note
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ). If the measured resistance is above 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again. If after 4 attempts the resistance is consistently lower than 0.050 mΩ (50 μΩ), the test has passed; continue to the next step.
  18. Repeat step 32 for the other charge port busbar connector lead and DC input HV header bolt head.
  19. Remove the HV insulating gloves and leather over gloves.
  20. Install the bolt that secures the charge port busbar connector access door.
    9 Nm (6.6 lbs-ft)
  21. Install the DC input HV header foam block.
  22. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  23. Install the LH and RH 2nd row seat side bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  24. Tighten the LH and RH front axle nuts.
    245 Nm (180.7 lbs-ft)
  25. Fasten the clip that attaches the frunk harness to the front drive unit.
  26. Connect the frunk harness to the front drive unit harness connector, and then push in the red tab to secure.
  27. Install the bolt that attaches the ground strap to the front drive unit.
    5.5 Nm (4.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is captive to the ground strap.
  28. Remove the steering wheel lock, and then remove the protector sheet from the driver seat.
  29. Perform a cooling system vacuum refill. See Cooling System (Vacuum Refill).
  30. Connect LV power. See LV Power (Disconnect and Connect).
  31. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  32. Perform a cooling system air purge. See Cooling System (Partial Refill and Bleed).
  33. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  34. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  35. Install the LH and RH rocker panel moldings. See Molding - Rocker Panel - LH (Remove and Replace).
  36. Install the LH and RH rocker panel scuff plates. See Scuff Plate - Rocker Panel - LH (Remove and Replace).
  37. Remove the vehicle from the 2 post lift. See Raise Vehicle - 2 Post Lift.
  38. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.