08/10/2024 17:34:38

Module - Body Controller - LH (Remove and Replace)

Correction code 17152102 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure. 17152102

  • 2023-11-13: Updated post-replacement routine.
  • 2023-04-19: Cleaned up.

Remove

  1. Remove the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  2. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Disconnect LV power. See LV Power (Disconnect and Connect).
  5. Remove the driver footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  6. Remove the driver knee airbag. See Knee Airbag - Driver (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    No need to remove the driver knee airbag cover.
  7. Fold the LH front cabin carpet aside for access.
  8. Use a clip prytool to release the clips (x2) that attach the LH harness bracket to the body.
  9. Use a clip prytool to release the clip that attaches the harness to the LH body controller.
  10. Disconnect the understood storage unit electrical connector (J9 X037) from the LH body controller module.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connectorJ9 X037
  11. Release the connector lock, and then disconnect the body 1 electrical connector (J1/J2 X030A/B) from the LH body controller module.
  12. Disconnect the body 3 electrical connector (J4 X032) from the LH body controller module.
  13. Release the connector lock, and then disconnect the body 5 electrical connector (J6/J7 X038A/B) from the LH body controller module.
  14. Release the connector lock, and then disconnect the body 4 electrical connector (J5 X034) from the LH body controller module.
  15. Release the connector lock, and then disconnect the body 2 electrical connector (J3 X031) from the LH body controller module.
  16. Disconnect the body 6 electrical connector (J8 X039) from the LH body controller module.
  17. Release the connector lock, and then disconnect the power electrical connector (J14 X036) from the LH body controller module.
  18. Disconnect the door 2 electrical connector (J11 X033B) from the LH body controller module.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  19. Disconnect the door electrical connector (J10 X033A) from the LH body controller module.
  20. Release the connector lock, and then disconnect the dash electrical connector (J12 X035) from the LH body controller module.
  21. Release the connector lock, and then disconnect the harness electrical connector.
  22. Move the harness bundle aside for access to the LH body controller.
  23. Remove and discard the nut that attaches the LH body controller to the body.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  24. Lift the LH body controller module upwards carefully to release the tab, and then remove the LH body controller module from the vehicle.

Install

  1. Install the LH body controller module to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Attach the tab onto the body and align into the body stud
  2. Install a new nut that attaches the LH body controller to the body.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  3. Position the harness bundle back to the LH body controller.
  4. Connect the harness electrical connector.
  5. Connect the dash electrical connector (J12 X035) to the LH body controller module.
  6. Connect the door electrical connector (J10 X033A) to the LH body controller module.
  7. Connect the door 2 electrical connector (J11 X033B) to the LH body controller module.
  8. Connect the power electrical connector (J14 X036) to the LH body controller module.
  9. Connect the body 6 electrical connector (J8 X039) to the LH body controller module.
  10. Connect the body 2 electrical connector (J3 X031) to the LH body controller module.
  11. Connect the body 4 electrical connector (J5 X034) to the LH body controller module.
  12. Connect the body 5 electrical connector (J6/J7 X038A/B) to the LH body controller module.
  13. Connect the body 3 electrical connector (J4 X032) to the LH body controller module.
  14. Connect the body 1 electrical connector (J1/J2 X030A/B) to the LH body controller module.
  15. Connect the understood storage unit electrical connector (J9 X037) to the LH body controller module.
  16. Fasten the clip that attaches the harness to the LH body controller.
  17. Fasten the clips (x2) that attach the LH harness bracket to the body.
  18. Return the LH main carpet back into place.
  19. Install the driver knee airbag. See Knee Airbag - Driver (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    No need to intstall the driver knee airbag cover.
  20. Install the driver footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  21. Connect LV power. See LV Power (Disconnect and Connect).
  22. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  23. In Toolbox 3, click the Actions tab, type "Service_Redeploy" into the search field, click UPDATE_CAN-REDEPLOYSearch for routine in ToolboxService CAN Redeployhv / Drive Inverter DIRE1L Replacement - CAN Redeployhv / Drive Inverter DIRE1R Replacement - CAN Redeployhv / Drive Inverter DIRE2 Replacement - CAN Redeployhv / Front Drive Inverter Replacement - CAN Redeployhv / Rear Drive Inverter Replacement - CAN Redeployhv / Rear Left Drive Inverter Replacement - CAN Redeployhv / Rear Right Drive Inverter Replacement - CAN Redeployhv / Front Drive Unit Replacement - CAN Redeployhv / Rear Drive Unit Replacement - CAN Redeploy, click Run, and allow the routine to complete.
  24. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  25. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  26. Install the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  27. Move the LH front seat back to its original position
  28. In Toolbox 3, click the Actions tab, type "VCLEFT replacement" into the search field, click PROC_VCLEFT_X_POST-REPLACEMENT-PROCEDURE, click Run, and allow the routine to complete.
  29. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).