17/06/2022 13:06:46

Window Motor/Regulator Assembly - Front - LH (Remove and Replace)

Correction code 11502002 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the LH front door trim decor. See Decor - Trim - Front Door - LH (Remove and Replace).
  3. Remove the LH front door panel. See Panel - Door Trim - Front - LH (Remove and Replace).
  4. Remove the LH front door glass. See Door Glass - Front - LH (Remove and Replace).
  5. Remove the plugs (x2) covering the openings in the door for access to the LH front regulator mounting guides
  6. Remove the LH front door closeout panel. See Closeout Panel - Door - Front - LH (Remove and Replace).
  7. Disconnect the LH front door speaker electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the tabs on either side of the connector.
  8. Remove the screws (x4) that attach the LH front door speaker to the spacer ring, and then lift the speaker upward and away from the spacer ring to remove it from the door assembly.
    1.8 Nm (1.3 lbs-ft)
  9. Lower the LH front door regulator isolator clamps partially.
    Informational PurposesAn informational icon, calling your attention
    Note
    The trailing clamp should be halfway down the door opening.
  10. Remove the lower nuts that attach the LH front window regulator to the door assembly.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Remove the butyl patches that cover the openings in door that access the upper LH front regulator mounting nuts.
  12. Remove the upper nuts (x2) that attach the LH front window regulator to the door assembly.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Remove the screws (x3) that attach the LH front window regulator motor to the door assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  14. Release the LH front window regulator from the upper mounts.
  15. Release the LH front window regulator from the lower mounts.
  16. Collapse and partially remove the LH front window regulator through the door opening with enough clearance to access motor harness connector
  17. Disconnect the LH front window regulator motor electrical connector.
  18. Remove the LH front window regulator from the door assembly.

Install

  1. Partially install the LH front window regulator into the door opening with enough clearance to access the motor harness electrical connector.
  2. Connect the LH front window regulator motor electrical connector.
  3. Secure the LH front window regulator into the lower mounts.
  4. Secure the LH front window regulator into the upper mounts.
  5. Install the screws (x3) that attach the LH front window regulator motor to the door assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  6. Install the upper nuts (x2) that attach the LH front window regulator to the door assembly.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install the butyl patches that cover the openings in door that access the upper LH front regulator mounting nuts.
  8. Install and hand-tighten the lower nuts that attach the LH front window regulator to the door assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Raise the LH front window regulator isolator clamps fully.
  10. Position the LH front door speaker onto the spacer ring, and then install the screws (x4) that attach the speaker to the spacer ring.
    1.8 Nm (1.3 lbs-ft)
  11. Connect the LH front door speaker electrical connector.
  12. Route the latch cable grommet through the opening in the LH front door closeout panel, and then install the grommet into the closeout panel assembly.
  13. Install the bolts (x6) that attach the LH front door closeout panel to the door assembly.
    4.5 Nm (3.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 2 in extension
  14. Fasten the clips (x2) that attach the wiring harness onto the LH front door closeout panel assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure there is an audible click to fully engage the clip.
  15. Connect the LH front door pressure sensor electrical connector, and then engage the connector lock.
  16. Install the screw that attaches the LH front door handle controller to the LH front door closeout panel.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  17. Connect the LH front door handle controller electrical connector, and then engage the connector lock.
  18. Install the LH front door glass. See Door Glass - Front - LH (Remove and Replace).