17/06/2022 13:01:49

Fascia Assembly - Rear (Remove and Install)

Correction Code: 10013001 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Set the air suspension ride height to “Very High” and place the vehicle into "Jack Mode".
  3. Open the hood.
  4. Open the liftgate.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect LV power. See LV Power (Disconnect and Connect).
  7. Remove the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace)
  8. Remove the trunk load floor.
  9. Remove the side load floor trim.
  10. Release the clips (x6) that attach the trunk sill trim to the vehicle, and then remove the trim from the vehicle.
  11. Release the clips (x4) that attach the rear wall trim to the vehicle, and then remove the trim from the vehicle.
  12. Release the clips (x3) that attach the LH trunk pocket bracket to the vehicle, and then remove the bracket from the vehicle.
  13. Pull the LH trunk side trim forward, and then secure the trim behind the side wall trim.
  14. Disconnect the LH trunk puddle lamp.
  15. Remove the butyl patch that covers the LH access hole.
  16. Remove the LH nut that attaches the rear fascia assembly to the body.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  17. Repeat step 12 through step 16 for the RH side of the vehicle.
  18. Remove the push clips (x4) that attach the LH rear wheel arch liner to the rear fascia, and then move the liner to the side for access.
  19. Remove the screw that attaches the rear fascia to the LH fender bracket.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  20. Repeat steps 18 and 19 for the RH side of the vehicle.
  21. Remove the nuts (x3) that attach the rear fascia diffuser to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  22. Remove the bolts (x8) and clips (x2) that attach the rear fascia diffuser to the mid aero shield panel, and then release the diffuser from the panel.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  23. Release the LH and RH rear fascia edges from the fender brackets.
    Figure 1. LH shown; RH similar
  24. Pull the rear fascia assembly rearward to release it from the body, but do not remove it from the vehicle as there is still an electrical connector connected.
  25. Pull the red tab to release the connector lock, and then disconnect the rear fascia electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector is located behind RH rear wheel arch liner.
  26. With assistance, remove the rear fascia assembly from the vehicle, and then place it on a padded surface.

Install

  1. With assistance, install the rear fascia assembly onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Route the fascia harness during installation. Verify that the rear diffuser sits under the mid aero shield panel before proceeding.
  2. Connect the rear fascia electrical connector, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector is located behind RH rear wheel arch liner.
  3. Secure the rear fascia assembly onto the body, and secure the fascia edges onto the fender brackets.
  4. Apply Loctite 222 to the bolts, and then install the bolts (x8) and clips (x2) that attach the rear fascia diffuser to the mid aero shield panel.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  5. Install the nuts (x3) that attach the rear fascia diffuser to the vehicle.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  6. Install the screw that attaches the rear fascia to the RH fender bracket.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 2. LH shown; RH similar
  7. Install the push clips (x4) that attach the LH rear wheel arch liner to the rear fascia.
    Figure 3. LH shown; RH similar
  8. Repeat steps 6 and 7 for the LH side of the vehicle.
  9. Install the LH nut that attaches the rear fascia assembly to the body.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
  10. Install the butyl patch that covers the LH access hole.
  11. Connect the LH trunk puddle lamp.
  12. Move the LH trunk side trim back into position.
  13. Position the LH trunk pocket bracket on the vehicle, and then install the clips (x4) that attach the bracket to the vehicle.
  14. Install the side load floor trim.
  15. Repeat step 9 through step 14 for the RH side of the vehicle.
  16. Position the rear wall trim on the vehicle, and then install the clips (x4) that attach the trim to the vehicle.
  17. Position the trunk sill trim on the vehicle, and then install the clips (x6) that attach the trim to the vehicle.
  18. Install the trunk load floor.
  19. Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace)
  20. Connect LV power. See LV Power (Disconnect and Connect).
  21. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  22. Close the hood.
  23. Remove the air suspension from "Jack Mode" and set to "Standard".
  24. Raise the LH front window and close the LH front door.