01/04/2024 14:03:54

Sensor - Parking Distance - Outer - Rear (HW3) (Remove and Replace)

17271122 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

Informational PurposesAn informational icon, calling your attention
Note
This procedure is applicable to sensors S7, S8, S11, and S12.
  1. On the vehicle touchscreen, touch Controls > Suspension > Very High.
  2. On the vehicle touchscreen, touch Controls > Service > Jack Mode to activate Jack Mode.
  3. Disconnect LV power. See LV Power (Disconnect and Connect).
  4. Remove the push clips (x4) that attach the rear wheel arch liner to the front fascia, and then move the wheel arch liner to the side.
  5. If servicing sensors 8 or 11:
    1. Remove the screw that attaches the rear fascia to the LH fender bracket.
      Informational PurposesAn informational icon, calling your attention
      Note
      1x screw, T25, 5 Nm, Flex liner against tire
    2. Release LH fascia edge from fender bracket.
  6. Disconnect the electrical harness from the parking distance sensor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Figure 1. Sensor 7 or 12
    Figure 2. Sensor 8 or 11
  7. Release the tabs that attach the parking distance sensor to the front fascia, and then remove the sensor from the fascia.

Install

  1. Position the parking distance sensor on the front fascia, and then attach the sensor to the front fascia.
  2. Connect the electrical harness to the parking distance sensor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
    Figure 3. Sensor 7 or 12
    Figure 4. Sensor 8 or 11
  3. If the rear fascia was partially released:
    1. Position the LH fascia edge to the fender bracket.
    2. Install the bolt that attaches the rear fascia to the LH fender bracket.
      Informational PurposesAn informational icon, calling your attention
      Note
      1x bolt, T25, 5 Nm
  4. Install the push clips (x5) that attach the LH rear wheel arch liner to the fascia.
  5. Connect LV power. See LV Power (Disconnect and Connect).
    Informational PurposesAn informational icon, calling your attention
    Note
    After connecting LV power, do not shift the vehicle to Drive until the Toolbox routine (further below) is performed. Failure to do so can trigger vehicle alerts.
  6. On the vehicle touchscreen, touch Controls > Service > Jack Mode to deactivate Jack Mode.
  7. On the vehicle touchscreen, touch Controls > Suspension > Standard.
  8. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  9. In Toolbox, click the Actions tab, type TEST-RESET_PARKSearch for routine in ToolboxPARK UDS ECU Reset into the search field, click TEST-RESET_PARKSearch for routine in ToolboxPARK UDS ECU Reset, click Run, and then allow the routine to complete.
  10. In Toolbox, click the Actions tab, type "USS Addresses" into the search field, click PROC_USM_REAR_PROGRAM-USS-ADDRESSESSearch for routine in ToolboxProgram Rear Ultrasonic Sensor AddressesDriver Assist / Sensors - Program Rear USS, click Run, and then allow the routine to complete.
  11. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  12. Raise the LH front window and close the LH front door.