30/05/2024 08:31:47

Hood Assembly (Remove and Replace)

Correction code 10100302 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the hood.
  2. With assistance, remove the nuts (x2) that attach the LH hood strut common bracket to the hood, and then set the hood strut aside. Repeat this step for the RH hood strut common bracket.
    15 Nm (11.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    Figure 1. LH shown; RH similar
    Figure 2. LH shown; RH similar
  3. With assistance, remove the nuts (x4) that attach the hood to the hinges, and then place the hood topside down on a portable bench.
    24 Nm (17.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    Figure 3. LH shown; RH similar
  4. Remove the hood aero seal from the hood. See Aero Seal - Hood (Remove and Replace).
  5. Remove the hood bumper-overslams (x4).
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate overslams counter-clockwise to remove.
  6. Remove the bolts (x2) that attach the hood striker to the hood, and then remove the striker from the hood.
    Tip: Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 3 in extension
    • Ratchet/torque wrench

Install

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
If using this procedure to install an unpainted part, make sure to apply seam sealer to all seams prior to installing and painting the part. Refer to the Collision Repair manual for more information.
  1. Install the hood striker onto the hood. See Striker - Hood (Remove and Replace).
  2. Install the hood striker to the hood, but do not fully torque the bolts.
  3. Install the hood bumper-overslams (x4).
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate overslams clockwise to install.
  4. Install the hood aero seal onto the hood. See Aero Seal - Hood (Remove and Replace).
  5. With assistance, position the hood onto the vehicle, and then install and hand-tighten the nuts (x4) that attach the hood to the hinges.
  6. With assistance, position the RH hood strut common bracket onto the hood, and then install the nuts (x2) that attach the bracket to the hood. Repeat this step for the LH hood strut common bracket.
    15 Nm (11.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    Figure 4. LH shown; RH similar
    Figure 5. LH shown; RH similar
  7. Close the hood and use a gap and flush tool to verify the hood gaps are within specification.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure the 10x points labeled in the image. Refer to CVIS for current specifications.
  8. Open the hood.
  9. Adjust the hood to achieve gap targets, and then hand tighten the nuts.
  10. Close the hood and use a gap and flush tool to verify the hood gaps are within specification.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure the 10x points labeled in the image. Refer to CVIS for current specifications.
  11. Open the hood.
  12. Torque the nuts (x4) that attach the hood to the hinges.
    24 Nm (17.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    Figure 6. LH shown; RH similar
  13. Torque the bolts that attach the hood striker to the hood.
    20 Nm (14.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 3 in extension
    • Ratchet/torque wrench
  14. Close the hood and use a gap and flush tool to verify the hood flushness is within specification.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure the 10x points labeled in the image. Refer to CVIS for current specifications.
  15. Open the hood.
  16. Adjust the hood to achieve flushness targets.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the bumper-overslams clockwise to decrease bumper height or counter-clockwise to increase bumper height as required to achieve flushness targets.
  17. Close the hood and use a gap and flush tool to verify the hood flushness is within specification.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure the 10x points labeled in the image. Refer to CVIS for current specifications.