20/06/2023 12:05:56

Duct - Floor - 2nd Row - RH (Remove and Replace)

Correction code 18109802 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open all four doors
  2. Lower all four windows
  3. Move LH front seat forward
  4. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  5. Move RH front seat forward
  6. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  7. Remove bolts securing rear of LH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal
  8. Remove bolts securing rear of RH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal
  9. Release console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 6x datums
  10. Remove console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 2x Datums, Slide panel rearward to disengage from console assembly, Connector lock for lamp located underneath bracket
  11. Release LH and RH rear console carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  12. Move LH front seat backward
  13. Move RH front seat backward
  14. Remove bolts securing front of LH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal
  15. Adjust position of LH front seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Note
    Move seat to middle of track at most upright position with seat fully up off floor
  16. Remove bolts securing front of RH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal
  17. Adjust position of RH front seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Note
    Move seat to middle of track at most upright position with seat fully up off floor
  18. Release phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
  19. Remove phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
  20. Release IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 4x datums, Release top tabs and slide rearward
  21. Release diagnostic and CAN harnesses from IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  22. Remove IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  23. Remove LH front floor mat
  24. Remove LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x magnets
  25. Remove LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs
  26. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  27. Remove LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips
  28. Release LH toeboard lower bracket from center console
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  29. Open hood
    Informational PurposesAn informational icon, calling your attention
    Note
    Using center display touchscreen > Quick Controls > Frunk Open
  30. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  31. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Safety & Security > Power Off
  32. Disconnect LV battery connector and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection
  33. Position chair to gain access below seat bottom and disconnect LH side body harness from seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 1x clip, Release red locking tab on black connector
  34. Remove LH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Use caution to not damage other components
  35. Position chair to gain access below seat bottom and disconnect RH side body harness from seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 1x clip, Release red locking tab on black connector
  36. Remove RH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Use caution to not damage other components
  37. Remove RH front floor mat
  38. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connector
  39. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs
  40. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  41. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips
  42. Release RH toeboard lower bracket from center console
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  43. Release center console connectors to body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors, 2x clips
  44. Release console carrier center bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  45. Remove console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift at rear, rotate front from under IP and out passenger door, Take care not to scratch seats, IP or inner door panel, Recommend assistance if needed
  46. Remove LH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Start by releasing upper portion
  47. Remove RH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Start by releasing upper portion
  48. Remove 2nd row seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x connectors, Disengage locking clips and lift up on seat cushion, Release connections, If 2nd row seats are folded down then fold up for time being
  49. Partially release LH lower C-pillar trim to access lower B-pillar clip
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  50. Remove LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 2x datums, Release from upper trim and body
  51. Partially release RH lower C-pillar trim to access lower B-pillar clip
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  52. Remove RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 2x datums, Release from upper trim and body
  53. Remove first row seat risers from cabin floor
    Informational PurposesAn informational icon, calling your attention
    Note
    4x risers, 2x clips
  54. Release cabin carpet from 2nd row seat sill
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  55. Remove cabin carpet from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold LH and RH front sections rearward
  56. Remove RH 2nd row floor duct
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  57. Install RH 2nd row floor duct
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  58. Install cabin carpet to vehicle
  59. Secure cabin carpet to 2nd row seat sill
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  60. Install first row seat risers to cabin floor
    Informational PurposesAn informational icon, calling your attention
    Note
    4x risers, 2x clips
  61. Install RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 2x datums, Align datums then engage all clips Replace any damaged or missing clips
  62. Secure partially released RH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Verify weather seal is seated properly
  63. Install LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 2x datums, Align datums then engage all clips Replace any damaged or missing clips
  64. Secure partially released LH lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Verify weather seal is seated properly
  65. Install 2nd row seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x connectors, Secure connections and slide seat belt buckles through seat cushion, Engage clips
  66. Install LH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top
  67. Install RH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top
  68. Install console assemby
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully maneuver front of assembly under and into IP carrier and lower rear into place, Recommend assistance if needed
  69. Secure LH toeboard lower bracket to center console
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  70. Secure RH toeboard lower bracket to center console
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  71. Secure center console connectors to body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors, 2x clips, Ensure all connector locks engaged
  72. Secure console carrier center bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  73. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs, Verify weather seal is seated properly
  74. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Verify weather seal is seated properly
  75. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips
  76. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connectors
  77. Install RH front floor mat
  78. Install RH front seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend Assistance, If seat is being replaced take note of OCS module revision, as this will determine the way firmware is installed to vehicle. Be cautious to avoid damage to surrounding components while lifting the seat into the vehicle.
  79. Position chair to gain access below seat bottom and connect RH side body harness to seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 1x clip, Engage red locking tab on black connector
  80. Install LH front seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend Assistance, Take care not to damage surrounding components while lifting the seat into the vehicle
  81. Position chair to gain access below seat bottom and connect LH side body harness to seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 1x clip, Engage red locking tab on black connector
  82. Connect First Responder Loop and LV battery connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
  83. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  84. Close hood
    Informational PurposesAn informational icon, calling your attention
    Note
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  85. Secure IP service panel connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  86. Secure diagnostic and CAN harnesses to IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  87. Install IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
  88. Install phone dock connections
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip, Note: If new center console assembly comes with phone dock re-use phone dock that is currently paired to vehicle, If replacing phone dock with new center console re-deploy CAN-ECU replacement firmware
  89. Install phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
  90. Move LH front seat backward
  91. Install bolts securing both LH front seat front tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new bolts
  92. Move RH front seat forward
  93. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  94. Install bolts securing both RH front seat front tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new bolts
  95. Install LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips
  96. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Verify weather seal is seated properly
  97. Install LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs, Verify weather seal is seated properly
  98. Install LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x magnets
  99. Install LH front floor mat
  100. Move LH front seat forward
  101. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  102. Install bolts securing LH front seat rear tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new bolts
  103. Move RH front seat forward
  104. Install bolts securing RH front seat rear tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new bolts
  105. Secure LH and RH rear console carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  106. Install console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 2x datums, Engage datums into console carrier slots
  107. Secure console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 6x datums
  108. Close RH rear door
  109. Move RH front seat to original position
  110. Close RH front door
  111. Move LH front seat to original position
  112. Raise all four windows
  113. Close LH front door
  114. Close LH rear door