04/06/2024 03:02:34

Brake Pads - Rear (Remove and Replace)

Correction code 33010802 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-06-04: Updated EPB Service Mode reference.
  • 2023-10-25: Updated EPB Service Mode reference.
  • 2023-10-16: Added step to make sure caliper piston face is aligned for Mando calipers.
  • 2023-3-24: Moved brake pedal pumping to before reservoir level check, and added precautionary steps for fluid spillage.

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Place absorbent material underneath the brake booster and the brake fluid reservoir area.
  3. Clean the area around brake fluid reservoir, and then remove the brake reservoir cap.
  4. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  5. Remove both rear wheels. See Wheel Assembly (Remove and Install).
  6. Place the vehicle into EPB Service Mode. See Park Brake Caliper - Release.
  7. Disconnect the EPB harness connector from the LH caliper motor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  8. Remove the LH rear caliper from the bracket and hang the caliper from the body.
  9. Use a caliper spreader kit or similar tool to gently push the piston back into the LH rear brake caliper.
  10. Remove the brake pads from the LH rear caliper bracket.
  11. Using a nylon brush, clean the LH rear brake caliper and anti-rattle springs.
  12. Repeat step 7 through step 11 for the RH side of the vehicle.

Install

  1. Apply an even layer of Silaramic lubricant to the LH rear brake pad contact points.
  2. Install the brake pads to the LH rear caliper bracket.
  3. If a Mando calipler, use needle-nose pliers to ensure that the slots in the rear brake caliper piston face are at the 12 o'clock and 6 o'clock positions.
  4. Install the bolts that attach the LH rear caliper to the caliper bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 14mm, 26 Nm
  5. Connect the LH EPB caliper harness connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the connector lock.
  6. Repeat step 1 through step 5 for the RH side of the vehicle.
  7. Hold the brake pedal and select "Park" on the touchscreen to disable the EPB service mode.
  8. Install both rear wheels. See Wheel Assembly (Remove and Install).
  9. Lower the vehicle.
  10. Pump the brake pedal repeatedly until firm to seat the brake pads against the rotors.
  11. Check brake fluid level and top off the reservoir, if necessary.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the brake fluid level is above the Max line, remove the extra brake fluid.
  12. Install the brake reservoir cap.
  13. Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
  14. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  15. Perform a vehicle road test using a series of ABS-active stops and make sure proper brake pedal feel and performance is achieved.