Correction code 20202012 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

1. Open LH front door
2. Lower LH front window
3. Press brake pedal to turn on drive rails
4. Set air suspension ride height to “Very High”
   Note

   Using center display > Controls > Suspension > ''Very High''
5. Turn wheel fully to the right
6. Open hood
   Note

   Via Center Display > Controls > Frunk Open
7. Remove rear underhood apron
   Note

   8x clips

   

   

8. Remove LH underhood apron
   Note

   10x clips

   

   

9. Remove RH underhood apron
   Note

   10x clips

   

   

10. Remove front underhood apron
    Note

    7x clips

    

    

11. Remove bolts securing fascia bracket to carrier
    Note

    6x bolts, 10mm, 4 Nm

    

12. Remove push clips securing LH front wheel arch liner to fascia and move to the side for access
    Note

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

13. Remove bolt securing front fascia to LH fender bracket
    Note

    1x bolt, T25, 5 Nm

    

14. Press brake pedal to turn on drive rails

    

15. Turn wheel fully to the left

    

16. Remove push clips securing RH front wheel arch liner to fascia and move to the side for access
    Note

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

17. Remove bolt securing front fascia to RH fender bracket
    Note

    1x bolt, T25, 5 Nm

    

18. Power off vehicle from center display
    Note

    Via Controls > Safety & Security > Power Off

    

19. Disconnect LV battery connector and First Responder Loop
    Note

    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection

    

    

    

    

20. Disconnect front fascia harness
    Note

    2x connectors, Pull red tab to disengage lock then disconnect, Located behind RH wheel arch liner

    

21. Release front fascia valance from front aero shield
    Note

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Do not remove 3x middle bolts

    

    

22. Release fascia from fender brackets and pull forward to remove from vehicle
    Note

    Set fascia on protected surface, Recommend assistance

    

    

23. Disconnect RH pressure tube sensor
    Note

    1x connector, release locking tab

    

24. Disconnect LH pressure tube sensor
    Note

    1x connector, release locking tab

    

25. Remove brush clips securing bumper foam onto front bumper beam
    Note

    4x Brush clips, Replace clips if damaged, 1x Bumper beam foam, replace if damaged

    

    

26. Remove bumper foam from vehicle

    

27. Remove pressure tube from bumper foam

    

    

    

    

28. Install pressure tube into bumper foam
    Note

    When inserting pedestrian protection sensor into foam assembly ensure the center marking on the tube lines up with the center inboard fir tree clip and that the tube is not twisted

    

    

    

    

29. Position bumper foam onto front bumper beam

    

30. Install brush clips securing bumper foam onto front bumper beam
    Note

    4x brush clips

    

31. Reconnect LH pressure tube sensor
    Note

    1x connector, secure locking tab

    

32. Reconnect RH pressure tube sensor
    Note

    1x connector, secure locking tab

    

33. Install front fascia onto vehicle and secure fascia to fender brackets
    Note

    Recommend Assistance, Route fascia harness while installing, Verify front fascia valance sits under front aero shield before proceeding

    

    

34. Apply Loctite 222 to fasteners and secure front fascia valance to front aero shield
    Note

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Insert valance datums into aero shield holes, Do not remove 3x middle bolts

    

    

    

35. Connect front fascia harness
    Note

    2x connectors, Engage locking tab, Located behind RH wheel arch liner

    

36. Install bolt securing fascia to RH fender bracket
    Note

    1x bolt, T25, 5 Nm

    

37. Install push clips securing RH front wheel liner to fascia
    Note

    5x push clips

    

    

38. Connect First Responder Loop and LV battery connector
    Note

    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

39. Press brake pedal to turn on drive rails

    

40. Turn wheel fully to the right

    

41. Install bolt securing fascia to LH fender bracket
    Note

    1x bolt, T25, 5 Nm

    

42. Install push clips securing LH front wheel liner to fascia
    Note

    5x push clips

    

    

43. Install bolts securing fascia bracket to carrier
    Note

    6x bolts, 10mm, 4 Nm

    

44. Install front underhood apron
    Note

    7x clips

    

    

45. Install RH underhood apron
    Note

    10x clips

    

    

46. Install LH underhood apron
    Note

    10x clips

    

    

47. Install rear underhood apron
    Note

    8x clips

    

    

48. Close hood
    Note

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

49. Press brake pedal to turn on drive rails
50. Turn steering wheel back to center
51. Remove air suspension from Jack Mode and set to "Standard"
    Note

    Using center display > Controls > Service > ''JACK MODE'', Using center display > Controls > Suspension > ''Standard''
52. Raise LH front window
53. Close LH front door