2026-08-06

Tie Rod Assembly - LH (Remove and Replace)

Correction code 32013202 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-08-06: Newly released procedure.

Remove

  1. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  2. Remove and discard the nut that attaches the LH tie rod to the knuckle assembly, and then release the tie rod from the knuckle.
    102 Nm (75.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  3. Remove and discard the large bellows clamp from bellows.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip 90 degree tip 6in
    • Small flat head screwdriver
  4. Remove bellows seal clip from bellows.
    Informational PurposesAn informational icon, calling your attention
    Note
    Flexible spring band clamp pliers.
  5. Slide bellows toward LH outer tie rod end.
    Informational PurposesAn informational icon, calling your attention
    Note
    You need to access the LH inner tie rod end inner ball joint.
  6. Remove LH tie rod assembly from pinion housing.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Breaker Bar 1/2in Dr. x Long - 1082458-00-A

Install

  1. Adjusting new tie rod length to match old tie rod before installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Combination Wrench 12pt 14mm
    • Combination Wrench 12pt 21mm
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn adjust inner tie rod as needed, parts line up is to count the threads on the removed tie rod then adjust to the same count on the new one, this will make alignment adjustment easier.
  2. Install LH inner tie rod assembly onto pinion housing.
    88 Nm (64.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended::
    • 38 crowfoot
    • 1/2 inch extension EXT-1/2IN-L125MM ZEBRA
    Informational PurposesAn informational icon, calling your attention
    Note
    Twist until it's fully seated.
  3. Slide bellows over pinion housing in preparation for clamping.
  4. Secure large bellows clamp onto bellows.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • JLR-211-342 STEERING GEAR CLAMP
  5. Secure bellows seal clip onto bellows.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Flexible spring band clamp pliers
  6. Install new nut that attaches the LH tie rod to the knuckle assembly, and then release the tie rod from the knuckle.
    102 Nm (75.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  7. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  8. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.