25/04/2024 10:05:58

Seat Back - 1st Row Seat - LH (Sport Seat) (Remove and Replace)

Correction code 13041112 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Seat Back - 1st Row Seat - LH (Sport Seat) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH front seat back to the seat assembly
5 Nm (3.7 lbs-ft)
  • 2 in extension
  • 10 mm socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
 Reuse

Remove

  1. Remove the driver seat headrest. See Headrest - Driver Seat (Sport Seat) (Remove and Replace).
  2. Remove the LH front seat décor assembly. See Decor Panel - 1st Row Seat - LH (Sport Seat) (Remove and Replace).
  3. Remove the LH front seat back panel. See Back Panel - LH (Sport Seat) \(Remove and Replace\).
  4. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  5. Disconnect LV power. See LV Power (Disconnect and Connect).
  6. Disconnect the LH front seat harness connectors (x2) from the seat back assembly.
  7. Release the clip that attaches the LH front seat harness to the seat back.
  8. Disconnect the LH front lumbar valve pack electrical connector.
  9. Remove the bolt that attaches the LH front seat back to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  10. Move the LH front seat seat back away from the seat frame to allow access to the 2nd row.
  11. Disconnect the LH front lumbar motor electrical connector.
  12. Release the clips (x2) that attach the LH front lumbar motor assembly to the seat assembly.
  13. Remove the LH front seat back assembly from the seat frame.

Install

  1. Install the LH front seat back assembly onto the seat frame.
  2. Position the LH front lumbar motor poutch onto the seat frame, and then secure the clips (x2) that attach the assembly to the seat.
  3. Connect the LH front lumbar motor electrical connector.
  4. Position the LH front seat back assembly onto the seat frame.
  5. Install the bolt that attaches the LH front seat back to the seat assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  6. Connect the LH front lumbar valve pack electrical connector.
  7. Install the clip that attaches the LH front seat harness to the seat back.
  8. Connect the LH front seat harness connectors (x2) to the seat back assembly.
  9. Connect LV power. See LV Power (Disconnect and Connect).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Install the LH front seat back panel. See Back Panel - LH (Sport Seat) \(Remove and Replace\).
  12. Install the LH front seat décor assembly. See Decor Panel - 1st Row Seat - LH (Sport Seat) (Remove and Replace).
  13. Install the driver seat headrest. See Headrest - Driver Seat (Sport Seat) (Remove and Replace).
  14. Raise the LH front window and close the LH doors.