19/06/2023 13:36:32

Lap Pretensioner - 1st Row - LH (Remove and Replace)

Correction code 20101002 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Move the driver seat forward and raise the seat to the highest position.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Adjust the seat back to avoid contact with the headliner, if necessary.
  3. Disconnect LV power. See LV Power (Disconnect and Connect).
  4. Remove the driver seat outboard side shield. See Side Shield - Outboard - Driver Seat (Remove and Replace).
  5. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  6. Remove the screw that attaches the driver seat outboard side shield to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  7. Carefully release the clips (x7) that attach the driver seat outboard side shield to the seat assembly, but do not fully remove the side shield from the seat assembly.
  8. Disconnect the electrical harness from the seat switch.
  9. Release the safety lock, and then disconnect the LH 1st row lap pretensioner electrical connector.
  10. Remove the bolt that attaches the LH 1st row lap pretensioner to the seat track, and then remove the pretensioner from the vehicle.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Bolt is patched and held in place with a metal clip.
    Tip: Use of the following tool(s) is recommended:
    • T50 socket

Install

  1. Position the LH 1st row lap pretensioner onto the seat track, align the guide pin onto the seat track, and then install the bolt that attaches the pretensioner to the seat assembly.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to use the new patch bolt that is included with the new pretensioner.
    Tip: Use of the following tool(s) is recommended:
    • T50 socket
  2. Connect the LH 1st row lap pretensioner electrical connector, and then secure the safety lock.
  3. Connect the electrical harness to the back rest and cushion adjust switch assembly, and then verify the functions of the seat switches.
  4. Position the driver seat outboard side shield onto the seat, and then install the clips (x7) that attach the side shield to the seat.
    Tip: Apply pressure to the side shield to fully seat the clips. The side shield should sit flush against the seat cushion.
  5. Install the screw that attaches the driver seat outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  6. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  7. Connect LV power. See LV Power (Disconnect and Connect).
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Close the hood.
  10. Move the driver seat to the original position.
  11. Raise the LH front window and close the LH front door.