2026-06-19

Perform General Inspection (Inspection)

Correction code 00030700 FRT 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check all windows from the master switch

Note
Check operation with door closed, Document any abnormal operation/noises
Function check LH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check RH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check RH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Verify operation of all exterior lights

Note
Recommend assistance, Headlamps, fog lights, license plate, tail, brake, reverse, & side repeater
Engage drive rails and activate windshield washer and wiper operation

Note
Engage drive rails and hold down on the washer button, Verify wipers and washer is operating as intended
Function check horn
Open hood

Note
Via Controls > Frunk Open
Remove rear underhood apron

Note
8x clips
Remove LH underhood apron

Note
10x clips, (*Use this step for Palladium S procedures)
Remove RH underhood apron

Note
10x clips
Remove front underhood apron

Note
7x clips
Remove frunk access panel

Note
3x clips, 3x hooks, 1x connector
Remove frunk carpet
Remove frunk assembly

Note
4x bolts, 10mm, 5 Nm
Perform inspection of under hood area

Note
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect brake fluid level
Inspect coolant level and top off as necessary

Note
Ensure that the fluid level is at the Max line, Top off fluid as required
Fill washer reservoir with fluid
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove front aero shield

Note
5x push clips
Release front aero shield

Note
9x bolts, 10mm, 6 Nm
Release rear aero shield

Note
4x push clips
Remove rear aero shield

Note
16x bolts, 10mm, 6 Nm
Perform inspection of vehicle underside components front and rear

Note
Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

Note
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of front suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Inspect underside of battery for damage
Check tire pressures

Note
4x tires, Adjust to specification if necessary
Inspect condition of LH front tire

Note
Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
Measure and record LH front tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Perform visual inspection of LH front brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Inspect condition of LH rear tire

Note
Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
Measure and record LH rear tread depth

Note
Record at least 3 measurements: Inner, Middle, Add line to replace if under 5/32 inch tread remaining
Perform visual inspection of LH rear brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Inspect condition of RH rear tire

Note
Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
Measure and record RH rear tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Perform visual inspection of RH rear brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect RH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Inspect condition of RH front tire

Note
Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
Measure and record RH front tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Perform visual inspection of RH front brake pads

Note
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect RH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Inspect brake hose condition

Note
Look for evidence of brake hose(s) rubbing on surrounding components, Inspect hose connections for evidence of leaks, Verify hoses are routed properly and secured to retaining brackets
Install rear aero shield

Note
16x bolts, 10mm, 6 Nm, Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle
Position rear aero shield

Note
4x push clips
Secure front aero shield to vehicle

Note
9x bolts, 10mm, 6 Nm, Apply Loctite 222 onto front aero shield bolts
Install front aero shield

Note
5x push clips
Lower vehicle fully

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Remove vehicle from lift

Note
Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
Install frunk assembly

Note
4x bolts, 10mm, 5 Nm
Install frunk carpet

Note
Verify carpet is properly seated under the seal
Install frunk access panel

Note
3x clips, 3x hooks, 1x connector
Install front underhood apron

Note
7x clips
Install RH underhood apron

Note
10x clips
Install LH underhood apron

Note
10x clips
Install rear underhood apron

Note
8x clips
Close hood

Note
Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

Note
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

Note
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction

Model S Service Manual

Perform General Inspection (Inspection)

Procedure

Figure 1

Figure 2

Figure 3