30/11/2023 00:25:12

Taillight - LH (Global) (Remove and Replace)

Correction code 17402012 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-11-30: Reorganized the procedure.
Informational PurposesAn informational icon, calling your attention
Note
This procedure is for the Global Refresh version of this part. The procedure for the Original version of this part is here: Taillight - LH (Remove and Replace).

Remove

  1. Remove the parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  2. Remove the trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  3. Remove the side trunk load floor. See Trunk Load Floor - Side (Remove and Replace).
  4. Remove the trunk sill panel. See Trim - Sill - Trunk (Remove and Replace).
  5. Remove the rear wall trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  6. Remove the LH trunk load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  7. Remove the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  8. Remove the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  9. Disconnect the LH taillight electrical connector.
  10. Remove the nuts (x2) that attach the LH taillight to the body.
    • Flex head ratchet/flex head torque wrench
    • 8 mm 12-point deep socket
    • 4 in extension
  11. Release the datum (x2) to remove the LH taillight from the body.

Install

  1. Hand-tighten the nuts that attach the taillight to the body.
  2. Use the body gap and flush tool to verify the fitment of the taillight to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Body Gap and Flush Tool - 1588903-00-A
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to the latest specifications in the Complete Vehicle Inspection Standards.
  3. If adjustment is necessary, remove the taillight from the vehicle.
  4. Position the adjustable datum in the center of the taillight to correct the taillight gap fitment and adjust the top threaded studs if additional clearance is needed.
  5. Secure the datums (x2) to attach the LH taillight to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, Note one datum clips into charge port door assembly, Verify body lamp is fully seated
  6. Install the nuts (x2) that attach the taillight to the body.
    3.5 Nm (2.6 lbs-ft)
    • Flex head ratchet/flex head torque wrench
    • 8 mm 12-point deep socket
    • 4 in extension
    • Ratchet/torque wrench
  7. Connect the LH taillight electrical connector.
  8. Install the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  9. Install the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  10. Install the LH trunk load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  11. Install the rear wall trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  12. Install the trunk sill panel. See Trim - Sill - Trunk (Remove and Replace).
  13. Install the side trunk load floor. See Trunk Load Floor - Side (Remove and Replace).
  14. Install the trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  15. Install the parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).