14/09/2022 15:04:25

Bracket - Toeboard - RH (Remove and Replace)

Correction code 15190022 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the RH front door and lower the RH front window.
  2. Move the front passenger seat fully rearward.
  3. Remove the RH front floor mat.
  4. Remove the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  5. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  6. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. Remove the RH center console side panel carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace).
  8. Remove the front passenger footrest panel. See Panel - Footrest - Front Passenger (LHD) (Remove and Replace).
  9. Release the clips (x3) that attach the electrical harness to the RH toeboard bracket and IP lower support, and then disconnect the electrical connectors (x2).
  10. Remove the bolts (x2) that attach the RH toeboard bracket to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Remove the bolt that attaches the RH toeboard lower bracket to the center console.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  12. Remove the bolt that attaches the RH toeboard upper bracket to the IP carrier.
    20 Nm (14.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  13. Slide the body side of the RH toeboard bracket up and out of the slotted receptacle, and then remove the bracket from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate the body harness and swing the rear of bracket out of the IP carrier.

Install

  1. Put the RH toeboard bracket in the vehicle by sliding the body side of the bracket down and into the slotted receptacle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Negotiate around the body harness and swing the rear of the bracket into the IP carrier.
  2. Install the bolts (x2) that attach the RH toeboard bracket to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the bolt that attaches the RH toeboard upper bracket to the IP carrier.
    20 Nm (14.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Install the bolt that attaches the RH toeboard lower bracket to the center console.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Connect the electrical connectors (x2), and then fasten the clips (x3) that attach the electrical harness to the RH toeboard bracket and IP lower support.
  6. Install the front passenger footrest panel. See Panel - Footrest - Front Passenger (LHD) (Remove and Replace).
  7. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  8. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  9. Install the RH center console side panel carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace).
  10. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  11. Install the RH front floor mat.
  12. Restore the front passenger seat back to its original position.
  13. Raise the RH front window and close the RH front door.