17/06/2022 13:14:25

Substrate - Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 13054702 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the LH 2nd row back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace).
  2. Remove the LH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  3. Remove the LH 2nd row backrest LH and RH headrest guides.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the headrest guide locking tabs and slide headrest guide out of frame assembly. Guide with adjustment button installed inboard.
  4. Disconnect the LH 2nd row backrest harness, and then release the clip that attaches the harness to the backrest.
  5. Disconnect the LH 2nd row backrest cushion heat pad electrical connector.
  6. Remove the bolts (x2) that attach the LH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Fold the LH 2nd row seat to the vertical position, but do not latch the seat back.
  8. Release the clips (x4) that attach the LH 2nd row backrest cushion to the backrest frame, and then remove the cushion assembly from the vehicle.
  9. Release the clips that attach the LH 2nd row backrest cushion heat pad harness to the LH 2nd row seat back substrate.
  10. Release the hooks (x4) that attach the bottom portion of LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  11. Release clips (x4) that attach the LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  12. Release the hooks (x6) and clips (x2) that attach the top portion of LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  13. Pull the top portion of LH 2nd row seat back trim down and off of the LH 2nd row seat back substrate.
  14. Remove the LH 2nd row seat back substrate from cushion assembly.
  15. Release the clip that attaches the LH 2nd row microphone harness to the LH 2nd row seat back substrate.
  16. Release the clips (x3) and tabs (x2) that attach the LH 2nd row microphone assembly to the LH 2nd row seat back substrate.

Install

  1. Position the LH 2nd row microphone assembly onto the LH 2nd row seat back substrate, and then install the clips (x3) and tabs (x2) that attach the harness to the substrate.
  2. Install the clip that attaches the LH 2nd row microphone harness to the LH 2nd row seat back substrate.
  3. Install the LH 2nd row seat back substrate into the cushion assembly.
  4. Pull the top portion of LH 2nd row seat back trim up and onto the LH 2nd row seat back substrate.
  5. Secure the hooks (x6) and clips (x2) that attach the top portion of LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  6. Fasten clips (x4) that attach the LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  7. Secure the hooks (x4) that attach the bottom portion of LH 2nd row seat back trim to the LH 2nd row seat back substrate.
  8. Fasten the clips (x2) that attach the LH 2nd row backrest cushion heat pad harness to the LH 2nd row seat back substrate.
  9. Position the LH 2nd row backrest cushion onto the backrest frame, and then fasten the clips (x4) that attach the cushion to the frame.
  10. Fold the LH 2nd row seat to the down position.
  11. Install the bolts (x2) that attach the LH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  12. Connect the LH 2nd row backrest cushion heat pad electrical connector.
  13. Fasten the clip that attaches the LH 2nd row backrest harness to the backrest, and then connect the electrical connector.
  14. Install the LH 2nd row backrest LH and RH headrest guides.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the guides into the backrest frame. Ensure the headrest guide locking tabs are fully engaged. Guide with adjustment button installed inboard.
  15. Install the LH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  16. Install the LH 2nd row back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace).