17/06/2022 13:12:21

Switch - Seat Fold - 2nd Row - RH (Remove and Replace)

Correction code 13020082 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the RH doors and lower the RH windows.
  2. Move the front passenger seat forward.
  3. Fold the RH 2nd row seat to the down position.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the 2nd lower seat cushion is not present, protect the seat as required.
  4. Remove the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  5. Release the clips (x2) that attach the RH 2nd row back side cover to the seat assembly, and then remove the cover from the seat assembly.
  6. Remove the clip that attaches the RH 2nd row shoulder plastic trim to the latch assembly.
  7. Remove the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace)
  8. Remove the RH 2nd row headrest guide locks. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
  9. Remove the bolts (x2) that attach the RH 2nd row backrest cushion to the frame assembly.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  10. Fold the RH 2nd row seat to the up position, but do not latch the seat back.
  11. Release the clips (x8) that attaches the RH 2nd row backrest cushion to the backrest frame, and then disconnect the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not remove the cushion from the vehicle.
  12. Remove the clips (x3) that attach the RH 2nd row shoulder plastic trim to the frame assembly.
  13. Release the clips (x6) that attach the RH 2nd row shoulder plastic trim to the frame assembly, then disconnect the fold switch electrical connector.
  14. Release the tabs (x2) that attach the RH 2nd row seat fold switch to the shoulder plastic trim, and then remove the switch from the trim.

Install

  1. Position the RH 2nd row seat fold switch onto the shoulder plastic trim, and then secure the tabs (x2) that attach the switch to the trim.
  2. Position the RH 2nd row shoulder plastic trim onto the seat frame assembly, connect the RH 2nd row seat fold switch electrical connector, and then secure the clips (x6).
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the fold switch with the frame gap to avoid damage.
  3. Install the clips (x3) that attach the RH 2nd row shoulder plastic trim to the frame assembly.
  4. Position the RH 2nd row backrest cushion to the backrest frame, connect the electrical connector, and then fasten the clips (x8).
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the lower clips then the connect backrest harness. Make sure all the clips are seated.
  5. Fold the RH 2nd row seat to the down position.
  6. Install the bolts (x2) that attach the RH 2nd row backrest cushion to the frame assembly.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Install the RH 2nd row headrest guide locks. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
  8. Remove the RH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace)
  9. Install the clip that attaches the RH 2nd row shoulder plastic trim to the latch assembly.
  10. Position the RH 2nd row back side cover to the seat assembly, and then install the clips (x2) that attach the cover to the seat assembly.
  11. Install the RH 2nd row seat back panel. See Back Panel – 2nd Row Seat – RH (Remove and Replace).
  12. Fold the RH 2nd row seat to the up position, and remove the seat protection if present.
  13. Move front passenger seat to the original position.
  14. Raise the RH windows and close the RH doors.