2022-06-17

Exterior Release Switch - Liftgate (Remove and Replace)

Correction code 11357002 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Apply tape around the liftgate, tail lights and applique.
  2. Remove the lower liftgate trim. See Trim - Liftgate - Lower (Remove and Replace).
  3. Remove the LH and RH rear fog/reverse light. See Light - Fog/Reverse - Rear - LH (Remove and Replace).
  4. Remove the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  5. Release the clips (x5) that attach the liftgate tail light and applique bracket assembly to the liftgate body, and then rest the bracket assembly on the liftgate.
  6. Remove the bolt that attaches the liftgate exterior release switch to the liftgate, and then release the switch from the liftgate.
    14.4 Nm (10.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Support the switch from the interior when released.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
    • Flex head ratchet/flex head torque wrench
  7. Disconnect the liftgate exterior release switch electrical connector.
  8. Remove the screws (x2) that attaches the liftgate exterior release switch to the release switch surround, and then separate the switch from the surround.
    3 Nm (2.2 lbs-ft) Nm
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit

Install

  1. Attach the liftgate exterior release switch to the release switch surround, and then install the screws (x2) that attach the switch to the surround.
    3 Nm (2.2 lbs-ft) Nm
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  2. Connect the liftgate exterior release switch electrical connector.
  3. Position the liftgate exterior release switch onto the liftgate, and then install the bolts that attach the release switch to the liftgate.
    14.4 Nm (10.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Support the release switch from the interior.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
    • Flex head ratchet/flex head torque wrench
  4. Fasten the clips (x5) that attach the liftgate tail light and applique bracket assembly to the liftgate body.
  5. Install the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply double sided tape as necessary.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  6. Install the LH and RH rear fog/reverse light. See Light - Fog/Reverse - Rear - LH (Remove and Replace).
  7. Remove the lower liftgate trim. See Trim - Liftgate - Lower (Remove and Replace).
  8. Remove the tape from the liftgate, tail lights and applique.