Diffuser - Fascia - Rear (Plaid) (2025+) (Remove and Replace)
Correction code
10010501902
0.00
NOTE: Unless
otherwise explicitly stated in the procedure, the correction code and its
associated FRT reflect all of the work required to perform this procedure,
including the linked procedures. Do not stack correction
codes unless explicitly told to do so.
NOTE: See Flat Rate Times to
learn more about FRTs and how they are created.
NOTE: See Personal Protection to make
sure you are wearing proper PPE when performing the procedure below.
NOTE: See Ergonomic Precautions for safe and healthy
working practices.
- 2026-09-02: Released new procedure.
Remove
-
Open LH front door
-
Lower LH front window
-
Set air suspension ride height to
“Very High”
NoteUsing center display > Controls > Suspension > ''Very High''
-
Open hood
NoteVia Controls > Frunk Open
-
Open liftgate through UI
NoteUsing center display touchscreen > Quick Controls > Trunk Open
-
Power off vehicle from center
display
NoteVia Controls > Safety & Security > Power Off
-
Remove rear underhood apron
Note8x clips
-
Disconnect LV battery connector and
First Responder Loop
Note2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection
-
Remove parcel shelf
-
Remove trunk load floor
-
Remove side load floor trim
-
Remove trunk sill panel
Note6x clips, 4x guidesCorners or bottom edge are good grabbing points for removal, Can use plastic trim tool or just your hands
-
Remove rear wall trim
Note4x push clips, 2x datums
-
Remove LH trunk bracket assembly
Note4x clips, 1x datum, Pull bracket straight up
-
Peel back LH trunk side trim and
secure behind side wall trim
-
Disconnect LH trunk puddle lamp
Note1x connector
-
Remove butyl patch covering LH access
hole
-
Remove LH nut securing rear fascia
assembly to body
Note1x nut, 10mm, 4 Nm
-
Remove RH trunk bracket assembly
Note3x clips, 1 datum, Pull bracket straight up
-
Peel back RH trunk side trim and
secure against upper C-pillar trim
-
Disconnect RH trunk puddle lamp
Note1x connector
-
Remove butyl patch covering RH access
hole
-
Remove RH nut securing rear fascia
assembly to body
Note1x nut, 10mm, 4 Nm
-
Remove push clips securing LH rear
wheel arch liner to fascia and move to the side for access
Note4x push clips
-
Remove screw securing rear fascia to
LH fender bracket
Note1x screw, T25, 5 Nm, Flex liner against tire
-
Remove push clips securing RH rear
wheel arch liner to fascia and move to the side for access
Note4x push clips
-
Remove screw securing rear fascia to
RH fender bracket
Note1x screw, T25, 5 Nm, Flex liner against tire
-
Remove rear diffuser nuts
Note3x nuts, 10mm, 3 Nm
-
Release rear diffuser from mid aero
shield
Note8x bolts, 10mm, 6 Nm, 2x clips, 2x datums
-
Apply protective tape
NoteApply protective tape to LH and RH rear fascia meeting edges .
-
Release LH and RH fascia edges from
fender brackets
-
Pull fascia rearward to release from
body
NotePull edges straight back to release fascia, Set fascia on protected surface, Recommend assistance
-
Remove rear fascia assembly from
vehicle
NoteSet fascia on protected surface, Recommend assistance,2x connectors, Disconnect BLE connectors before removing fascia, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
-
Flip rear fascia assembly upright on
workbench
-
Remove rear fascia diffuser
fasteners
Note6x bolts, 10mm, 5 Nm, 12x clips
-
Remove rear fascia diffuser
Install
-
Install rear fascia diffuser
fasteners
Note6x bolts, 10mm, 5 Nm, 12x clips
-
Secure rear fascia assembly onto
body
NoteSecure fascia edges onto fender brackets
-
Apply Loctite 222 to fasteners and
secure rear diffuser to mid aero shield
Note8x bolts, 10mm, 6 Nm, 2x clips, 2x datums
-
Install rear diffuser nuts
Note3x nuts, 10mm, 3 Nm
-
Install bolt securing rear fascia to
RH fender bracket
Note1x bolt, T25, 5 Nm
-
Install push clips securing RH rear
wheel arch liner to fascia
Note4x push clips
-
Install bolt securing rear fascia to
LH fender bracket
Note1x bolt, T25, 5 Nm
-
Install push clips securing LH rear
wheel arch liner to fascia
Note5x push clips
-
Install LH nut securing rear fascia
assembly to body
Note1x nut, 10mm, 4 Nm
-
Install butyl patch covering LH access
hole
-
Connect LH trunk puddle lamp
Note1x connector
-
Secure LH trunk side trim back into
place
-
Install LH trunk bracket
assembly
Note4x clips, 1 datum
-
Install side load floor
-
Install RH nut securing rear fascia
assembly to body
Note1x nut, 10mm, 4 Nm
-
Install butyl patch covering RH access
hole
-
Connect RH trunk puddle lamp
Note1x connector
-
Secure RH trunk side trim back into
place
-
Install RH trunk bracket
assembly
Note3x clips, 1 datum
-
Install rear wall trim
Note4x push clips, 2x datums
-
Install trunk sill panel
Note6x clips, 4x guides
-
Install trunk load floor
-
Install parcel shelf
-
Connect First Responder Loop and LV
battery connector
Note2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
-
Close liftgate
-
Install rear underhood apron
Note8x clips
-
Close hood
NotePress firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
-
Raise LH front window
-
Close LH front door
Note