17/06/2022 13:07:08

Closeout Panel - Door - Front - LH (Remove and Replace)

Correction code 11701032 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the LH front door trim decor. See .
  3. Remove the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace)
  4. Pull the white tab to release the connector lock, and then disconnect the LH front door handle controller electrical connector.
  5. Remove the screw that attaches the LH front door handle controller to the LH front door closeout panel.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  6. Release the retainer tabs that attach the LH front door handle controller to the LH front door closeout panel assembly, and then remove the controller from the assembly.
  7. Disconnect the LH front door pressure sensor electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  8. Remove the bolts (x6) that attach the LH front door closeout panel to the door assembly.
    4.5 Nm (3.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 2 in extension
  9. Release the latch cable grommet from the closeout panel assembly, and then route the grommet and cable through the opening.
  10. Release the clips (x2) that attach the wiring harness to the LH front door closeout panel assembly, and then remove the closeout panel from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release clips from back of the panel to prevent damage.

Install

  1. Route the latch cable grommet through the opening in the LH front door closeout panel, and then install the grommet into the closeout panel assembly.
  2. Install the bolts (x6) that attach the LH front door closeout panel to the door assembly.
    4.5 Nm (3.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
    • 2 in extension
  3. Fasten the clips (x2) that attach the wiring harness onto the LH front door closeout panel assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure there is an audible click to fully engage the clip.
  4. Connect the LH front door pressure sensor electrical connector, and then engage the connector lock.
  5. Install the LH front door handle controller onto the LH front door closeout panel assembly.
  6. Install the screw that attaches the LH front door handle controller to the LH front door closeout panel.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 2 in extension
  7. Connect the LH front door handle controller electrical connector, and then engage the connector lock.
  8. Install the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace)
  9. Install the LH front door trim decor. See .
  10. Raise the LH front window and close the LH front door.