17/06/2022 13:26:04

Harness - 2nd Row Seat - LH (Remove and Replace)

Correction code 17100072 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower all the windows.
  2. Move the front seats forward.
  3. Remove the LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  4. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. Remove and discard the bolt that attaches the 2nd row center seat belt lower anchor to the vehicle, and then release the lower anchor from the vehicle.
    25 Nm (18.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  6. Fold the LH 2nd row seat to the down position.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the seat cushion is not present, protect the seat as required.
  7. Remove the LH 2nd row seat back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace).
  8. Remove the LH 2nd row seat back side cover. See Cover - Side - Seat Back - 2nd Row - LH (Remove and Replace).
  9. Remove the LH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  10. Remove the LH 2nd row backrest LH and RH headrest guides.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the headrest guide locking tabs and slide headrest guide out of frame assembly. Guide with adjustment button installed inboard.
  11. Disconnect the LH 2nd row backrest harness, and then release the clip that attaches the harness to the backrest.
  12. Disconnect the LH 2nd row backrest cushion heat pad electrical connector.
  13. Remove the bolts (x2) that attach the LH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  14. Fold the LH 2nd row seat to the vertical position, but do not latch the seat back.
  15. Release the clips (x4) that attach the LH 2nd row backrest cushion to the backrest frame, and then remove the cushion assembly from the vehicle.
  16. Remove the clips (x3) that attach the LH 2nd row seat shoulder plastic trim to the seat assembly.
  17. Release the clips (x5) that attach the LH 2nd row shoulder plastic trim to the frame assembly, and then partially release the shoulder plastic trim and set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the fold switch harness and connector are not excessively pulled. Use a plastic trim tool or shop towel to hold the trim away from the seat frame.
  18. Pull the red tab to release the connector lock, and then disconnect the LH 2nd row seat seat back latch electrical connector.
  19. Fold the LH 2nd row seat to the down position.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the seat cushion is not present, protect the seat as required.
  20. Disconnect the LH 2nd row seat back harness electrical connector.
  21. Release the clip that attaches the LH 2nd row seat back harness to the pivot bracket.
  22. Release the pivot bushing that attaches the LH 2nd row seat back assembly to the pivot bracket.
  23. Slightly tilt the LH 2nd row seat back upward, and then pull the LH 2nd row pivot cast upward to release it from the pivot bracket.
  24. Release the LH 2nd row seat back from the RH pivot, and then remove the seat back from the vehicle.
  25. Place the LH 2nd row seat back assembly upside down on a padded workbench.
  26. Remove the bolt that attaches the LH 2nd row seat bolster assembly to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  27. Release the locking tab, and then disconnect the 2nd row center armrest harness electrical connector.
  28. Position the LH 2nd row seat back to the upright on the padded workbench.
  29. Release the clips (x2) that attach the LH 2nd row bolster assembly to the seat assembly, and then remove the bolster from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lightly squeeze the clips to release the sub-bolster.
  30. Remove the clips (x2) that attach the 2nd row armrest bun to the seat assembly.
  31. Release the clips (x3) that attach the 2nd row armrest bun to the seat back assembly, and then remove the bun from the assembly.
  32. Release the clips (x7) that attach the LH 2nd row seat harness to the seat assembly, and then route the armrest connector under the armrest plastic trim to remove the harness from the assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pinch the harness.

Install

  1. Position the LH 2nd row seat harness into the LH 2nd row seat back assembly, route the armrest electrical connector under the armrest plastic trim, and then install the clips that attach the harness to the assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pinch the harness.
  2. Install the clips (x3) that attach the 2nd row armrest bun to the seat back assembly.
  3. Install the clips (x2) that attach the 2nd row armrest bun to the seat assembly.
  4. Install the clips (x2) that attach the LH 2nd row bolster assembly to the seat assembly.
  5. Position the seat back assembly upside down on the padded workbench.
  6. Connect the LH 2nd row center armrest harness electrical connector, and then engage the locking tab.
  7. Install the bolt that attaches the LH 2nd row seat bolster assembly to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Position the LH 2nd row seat back into the vehicle, and then secure the seat back into the RH pivot.
  9. Slightly tilt the LH 2nd row seat back upward, and then press the LH 2nd row pivot cast downward to secure it to the pivot bracket.
  10. Install the pivot bushing that attaches the LH 2nd row seat back assembly to the pivot bracket.
  11. Fasten the clip that attaches the LH 2nd row seat back harness to the pivot bracket.
  12. Connect the LH 2nd row seat back harness electrical connector.
  13. Fold the LH 2nd row seat to the up position.
  14. Connect the LH 2nd row seat seat back latch electrical connector, and then engage the connector lock.
  15. Position the LH 2nd row shoulder plastic trim to the seat assembly, and then fasten the clips (x5) that attach the trim to the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the plastic trim tool or shop towel. Ensure the fold switch harness and connector are properly placed.
  16. Install the clips (x3) that attach the LH 2nd row seat shoulder plastic trim to the seat assembly.
  17. Install the clips (x4) that attach the LH 2nd row backrest cushion to the seat assembly.
  18. Fold LH 2nd row seat to the down position.
  19. Install the bolts (x2) that attach the LH 2nd row backrest cushion to the back frame.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  20. Connect the LH 2nd row backrest cushion heat pad electrical connector.
  21. Fasten the clip that attaches the LH 2nd row backrest harness to the backrest, and then connect the electrical connector.
  22. Install the LH 2nd row backrest LH and RH headrest guides.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the guides into the backrest frame. Ensure the headrest guide locking tabs are fully engaged. Guide with adjustment button installed inboard.
  23. Install the LH 2nd row headrest. See Headrest - 2nd Row - LH (Remove and Replace).
  24. Install the LH 2nd row seat back side cover. See Cover - Side - Seat Back - 2nd Row - LH (Remove and Replace).
  25. Install the LH 2nd row seat back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace)
  26. Fold 60 seat into vertical position
  27. Install a new bolt that attaches the 2nd row center seat belt lower anchor to the vehicle.
    25 Nm (18.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  28. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  29. Install the LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  30. Move the front seats to the original positions.
  31. Raise all four windows
  32. Raise all the windows and close all the doors.