01/03/2023 09:19:40

Fascia Assembly - Rear (HW4) (Remove and Replace)

Correction code 10013012 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the rear fascia assembly. See Fascia Assembly - Rear (Remove and Install).
  2. Remove the screws (x2) that attach the LH rear BLE assembly to the rear fascia, and then remove the assembly from the fascia. Repeat this step for the RH rear BLE assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 1. LH shown; RH similar
    Figure 2. LH shown; RH similar
  3. Remove the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    Figure 3. LH shown; RH similar
  4. Position the rear fascia assembly upside down on workbench.
  5. Remove the screws (x2) and release the tabs (x10) that attach the tow hitch cover to the rear fascia assembly, and then remove the cover from the assembly.
    Tip: Use of the following tool(s) is recommended:
    • Large flathead screwdriver
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Plastic screws are captive. Be careful to avoid damage.
  6. Remove the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  7. Position the rear fascia assembly upright on the workbench.
  8. Release the tabs (x8) that attach the rear diffuser to the rear fascia assembly, and then remove the diffuser from the assembly.
  9. Remove the bolts (x2) that attach the rear lower fascia to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  10. Release the tabs (x23) that attach the rear lower fascia to the rear fascia assembly, and then remove the lower fascia from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Insert a pick behind the lower fascia tab, and the rotate to pry the fascia assembly tab upward.

Install

  1. Place the new rear fascia assembly upside down on flat and protected surface.
  2. Position the rear lower fascia onto the rear fascia assembly, and then secure the tabs (x23) that attach the lower fascia to the assembly.
    Figure 4. LH shown; RH similar
  3. Place the rear fascia assembly upright on the workbench.
  4. Install the bolts that attach the rear lower fascia to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  5. Position the rear diffuser onto rear fascia assembly, and then secure the tabs (x8) that attach the diffuser to the fascia.
  6. Install the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    Figure 5. LH shown; RH similar
  7. Place the rear fascia assembly upside down on workbench.
  8. Install the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  9. Position the tow hitch cover onto the rear fascia assembly, and then secure the tabs (x10) that attach the cover to the fascia.
  10. Install the bolts that attach the tow hitch cover to the rear fascia.
    Tip: Use of the following tool(s) is recommended:
    • Large flathead screwdriver
    Informational PurposesAn informational icon, calling your attention
    Note
    Plastic screws are captive. Be careful to avoid damage.
  11. Place the rear fascia assembly upright on workbench.
  12. Position the RH rear BLE assembly onto the rear fascia, and then install the screws that attach the BLE assembly to the fascia. Repeat this step for the LH BLE assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 6. LH shown; RH similar
  13. Install the rear fascia assembly. See Fascia Assembly - Rear (Remove and Install).