Retractor - Seatbelt - 2nd Row - LH (Remove and Replace)
Correction code 20056102 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open all the doors and lower the LH front window.
- Move the front seats forward.
- Open the liftgate.
- Remove the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
- Remove LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
- Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
-
Fold the LH 2nd row seat back to the
down position.
NoteIf seat cushion is not present, protect the seat as required.
- Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Disconnect LV power. See LV Power (Disconnect and Connect).
- Remove the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
-
Release the clips (x7) that attach the
LH upper C-pillar trim to the vehicle, and then move the trim aside.
-
Remove the clip that attaches the LH
trunk side trim to the vehicle, and then partially release the trim from the
assembly.
-
Remove and discard the lower bolt that
attaches the LH 2nd row seatbelt to the body.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
-
Remove and discard the upper bolt that
attaches the LH 2nd row seatbelt to seatbelt bracket.Tip: Use of the following tool(s) is recommended:
- T50 socket
-
Disconnect the LH 2nd row seatbelt
electrical connector.
-
Remove and discard the nut that
attaches the LH 2nd row seatbelt to the vehicle, and then remove the seatbelt from the
vehicle.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
Install
-
Position the LH 2nd row seatbelt into the vehicle, and then install a new nut that
attaches the seatbelt to the vehicle.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
-
Connect the LH 2nd row seatbelt electrical connector.
-
Install a new upper bolt that attaches the LH 2nd row seatbelt to seatbelt
bracket.Tip: Use of the following tool(s) is recommended:
- T50 socket
-
Install a new lower bolt that attaches the LH 2nd row seatbelt to the body.Tip: Use of the following tool(s) is recommended:
- 15 mm socket
-
Move the LH trunk side trim into position, and then install the clip.
-
Move the LH upper C-pillar trim into
position, and then secure the clips (x7) that attach the trim to the pillar.
- Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
- Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Fold the LH 2nd row seat back to the up position.
- Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
- Install LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
- Connect LV power. See LV Power (Disconnect and Connect).
- Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
- Close the liftgate.
- Move the front seats to the original positions.
- Raise all the windows and close all the doors.