22/09/2022 14:42:51

ECU - Charge Port (Remove and Replace)

Correction code 44015002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
Note
This procedure is for the Original version of this part. An updated/region-specific Global Refresh version of this part is available for newer vehicles and that procedure is here: ECU - Charge Port (Global) (Remove and Replace).

Remove

  1. Fold the LH 2nd row seat (60 split) in the down position.
  2. Remove the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  3. Remove the trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  4. Remove the rear wall rear trunk trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  5. Remove the side trunk load floor. See Trunk Load Floor - Side (Remove and Replace).
  6. Remove the LH trunk load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  7. Remove the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  8. Remove the LH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  9. Release the clips (x4) that attach the LH lower C-pillar trim to the LH mid C-pillar trim.
  10. Remove LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  11. Release the clips (x7) that attach the LH upper C-pillar trim to the body, and then move it aside. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  12. Remove the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  13. Disconnect the charge port ECU connectors (x3).
  14. Remove the bolt that attaches the charge port ECU to the bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    10mm. Torque 4 Nm.
  15. Release the tabs (x2) and then move upward the charge port ECU onto the bracket. Remove the ECU from the vehicle.

Install

  1. Slide down to engage the tabs (x2) that attach the bracket the charge port ECU.
  2. Install the bolt that attach the charge port ECU to the bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    10mm. Torque 4 Nm.
  3. Connect the charge port ECU electrical connectors (x3).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Once the new ECU is installed, immediately start the software reinstall described in the following steps, as delays might cause excessive LV battery drain.
  4. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  5. Click Actions/Autodiag and then search for Redeploy.
  6. Click SERVICE CAN REDEPLOY, then click Run. Allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click X at top right of the window to close once completed. Routine will state pass but update will continue to run in the background. UI will indicate status of update.
  7. Disconnect Toolbox 3 from the vehicle, and then remove the laptop and the ethernet diag kit.
  8. Install the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  9. Secure the clips (x7) that attach the LH upper C-pillar trim to the body.
  10. Install LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  11. Secure the clips (x4) that attach the LH lower C-pillar trim onto the LH mid C-pillar trim.
  12. Install the LH 2nd row seat outer bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  13. Install the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  14. Install the LH trunk load floor bracket. See Bracket - Trunk Load Floor - LH (Remove and Replace).
  15. Install the rear wall rear trunk trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  16. Install the side trunk load floor. See Trunk Load Floor - Side (Remove and Replace).
  17. Install the trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  18. Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  19. Close the liftgate.
  20. Fold the LH 2nd row (60 split) seat into vertical position.
  21. Close the LH rear door.