2023-12-20

Tire - Front - LH (Remove and Replace)

Correction code 34021002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-05-23: Added caution about lubricant drying time.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
It may take up to 24 hours before the tire lubricant has dried completely. Do not perform any fast accelerations during this period to avoid tire slip on the rim.
  1. Remove the LH front wheel. See Wheel Assembly (Remove and Install)
  2. Remove valve stem cap
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cap
  3. Remove valve stem core
    Informational PurposesAn informational icon, calling your attention
    Note
    Exercise caution as tire rapidly deflates, wear appropriate PPE
  4. Place wheel on tire machine and secure
    Informational PurposesAn informational icon, calling your attention
    Note
    1x wheel clamp
  5. Rotate tire and wheel so that upper roller is 100mm in front of the valve
  6. Break tire beads
    Informational PurposesAn informational icon, calling your attention
    Note
    Use lubrication around tire and wheel
  7. Remove tire from wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to position the TPMS sensor ahead of the tire machine arm
  8. Thoroughly lubricate both beads and mount new tire
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to position the TPMS sensor opposite the tire machine arm. If the tire has "outside", "side facing outwards", or a direction of rotation arrow on the sidewall, ensure that the tire is oriented properly
  9. Inflate the tire to seat the bead
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not exceed the pressure indicated on the tire sidewall, Wear PPE
  10. Install valve core stem and then remove wheel from mounting machine
  11. Mount tire and wheel assembly on balancer
    Informational PurposesAn informational icon, calling your attention
    Note
    1x tire machine wing nut
  12. Remove wheel weights
  13. Place Wheel/Tire on Balance Machine and secure lock nut
  14. Verify tire pressure is set
    Informational PurposesAn informational icon, calling your attention
    Note
    Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar
  15. Input wheel dimensions into balancer machine
  16. Spin wheel to check balance
  17. Install weights in positions indicated by machine
  18. Perform check spin
  19. Remove tire and wheel assembly from tire balancer
    Informational PurposesAn informational icon, calling your attention
    Note
    1x tire balancer wing nut
  20. Install the LH front wheel. See Wheel Assembly (Remove and Install)