17/06/2022 13:15:11

Foam - Back Rest - Driver Seat (With Inboard Airbag) (Remove and Replace)

Correction code 13072612 1.26 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the driver seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).
  2. With assistance, place the driver seat on a protected surface so that the underside of the seat can be accessed.
  3. Remove the screw that attaches the driver seat outboard side shield to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  4. Carefully release the clips (x7) that attach the driver seat outboard side shield to the seat assembly, but do not fully remove the side shield from the seat assembly.
  5. Disconnect the electrical harness from the seat switch.
  6. Remove the front seat side shield LH carrier from the driver seat. See .
  7. Remove the driver seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
  8. Remove the front seat side shield RH carrier from the driver seat. See Carrier - RH - Side Shield - Inboard - Front Seat (Remove and Replace).
  9. Release the seat back elastic straps (x2) from the seat frame.
  10. Disconnect the FSB vent heat pad electrical connector from the driver seat controller.
  11. Release the clip and bracket that attach the FSC and FSB vent heat pad harnesses to the seat assembly, and then remove the harnesses from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    One harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them.
  12. Remove the driver seat headrest. See Trim - Headrest - Driver (Remove and Replace).
  13. Remove the driver seat back shell. See Shell - Seat Back - Driver (Remove and Replace).
  14. Disconnect the fan controller electrical connector from the seat harness.
  15. Disconnect the driver seat microphone electrical connector, and then release clip that attaches the harness to the driver seat back rest foam.
  16. Release the female side of the microphone connector and harness clips (x2) from the seat back suspension.
  17. Release the trim strap, and then release the trim retainers (x6) that attach the seat back trim retainers to the seat back frame.
  18. Carefully release the driver seat cover from the driver seat, and then set the cover aside for access.
  19. Push down on the tab to release the driver seat side air bag electrical connector, and then disconnect the connector.
  20. Release the clip that attaches the driver seat side air bag harness to the driver seat seat frame.
  21. Remove the bolt that attaches the driver seat backrest lumbar support to the seat back frame.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  22. Release the tabs (x2) that attach the lower portion of the driver seat backrest lumbar support to the seat back frame.
  23. Carefully pull the seat cover and foam assembly away from the frame, and then remove and discard the nuts (x2) that attach the driver seat side air bag to the seat back frame assembly.
    5.4 Nm (4.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  24. Release the RH side of the driver seat back trim assembly, and then move the trim aside for access.
  25. Push down on the tab to release the driver seat inboard side air bag electrical connector, and then disconnect the connector.
  26. Release the clip that attaches the driver seat harness to the RH side of seat back frame.
  27. Carefully pull the seat cover and foam assembly away from the frame, and then remove and discard the nuts (x2) that attach the driver seat inboard side air bag to the seat back frame assembly.
    5.4 Nm (4.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  28. With assistance, remove the driver seat back trim assembly from the seat frame.
  29. Unfold the seat back trim from the LH side bolster, and then carefully remove the air bag chute from the LH side of the seat back foam.
  30. Unfold the seat back trim from the RH side bolster, and then carefully remove the air bag chute from the RH side of the seat back foam.
  31. Release the Velcro strips (x4) that attach the driver seat back rest trim to the seat back rest foam, and then remove the trim from the assembly.
  32. Remove the driver seat microphone assembly from the driver seat back rest foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed the harness through the access hole on the driver seat back rest foam.

Install

  1. Position the driver seat microphone onto the driver back rest foam, and then feed the harness through the access on the foam to install the microphone onto the foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed harness through access hole on seat back foam
  2. Position the driver seat back rest trim onto the driver seat back rest foam, and then align the Velcro strips (x4).
  3. Carefully position the air bag chute into the RH side of the seat back foam, and then fold the seat back trim over the RH side bolster.
  4. Carefully position the air bag chute into the LH side of the seat back foam, and then fold the seat back trim over the LH side bolster.
  5. With assistance, maneuver the driver seat back trim assembly downward onto the seat frame to install it onto the seat assembly.
  6. Install new nuts (x2) that attach the driver seat inboard side air bag to the seat back frame assembly.
    5.4 Nm (4.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  7. Install the clip that attaches the driver seat harness to the RH side of seat back frame.
  8. Connect the driver seat inboard side air bag electrical connector, and then secure the safety lock.
  9. Carefully secure the RH side of the driver seat back trim onto the driver seat frame.
  10. Install new nuts (x2) that attach the driver seat side air bag to the seat back frame assembly.
    5.4 Nm (4.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  11. Fasten the tabs (x2) that attach the lower portion of the driver seat backrest lumbar support to the seat back frame.
  12. Install the bolt that attaches the driver seat backrest lumbar support to the seat back frame.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Install the clip that attaches the driver seat side air bag harness to the driver seat seat frame.
  14. Connect the driver seat side air bag electrical connector, and then secure the safety lock.
  15. Carefully secure the LH side of the driver seat seat cover and foam onto the seat frame.
  16. Secure the retainers (x6), and then secure the trim strap onto the driver seat seat back frame.
  17. Secure the female side of microphone connector and harness clips (x2) onto seat back suspension.
  18. Connect the driver seat microphone, and then secure harness clip onto the seat back foam.
  19. Slide the fan controller electrical connector downward to install it onto the bracket, and then connect the electrical connector.
  20. With assistance, align and fully secure the clips that attach the driver seat back shell to the seat assembly.
  21. Install the driver headrest trim. See Trim - Headrest - Driver (Remove and Replace).
  22. Position the driver seat assembly onto the seat back.
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect the seat from damage.
  23. Secure the clip and bracket that attach the FSC and FSB vent heat pad harnesses to the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    One harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them.
  24. Connect the FSB vent heat pad electrical connector from the seat controller.
  25. Secure the seat back elastic straps (x2) to the seat frame.
  26. Install the front seat side shield RH carrier from the driver seat. See Carrier - RH - Side Shield - Inboard - Front Seat (Remove and Replace).
  27. Install the driver seat inboard side shield. See Side Shield - Inboard - Driver Seat (Remove and Replace).
  28. Install the front seat side shield LH carrier from the driver seat. See .
  29. Connect the electrical harness to the back rest and cushion adjust switch assembly, and then verify the functions of the seat switches.
  30. Position the driver seat outboard side shield onto the seat, and then install the clips (x7) that attach the side shield to the seat.
    Tip: Apply pressure to the side shield to fully seat the clips. The side shield should sit flush against the seat cushion.
  31. Install the screw that attaches the driver seat outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  32. Install the driver seat into the vehicle. See Seat Assembly - 1st Row - LH (Remove and Replace).