24/10/2023 06:38:47

Seat Assembly - 1st Row - LH (Remove and Replace)

Correction code 13040102 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Informational PurposesAn informational icon, calling your attention
Note
The front seats contain airbags and pretensioners and therefore must be disposed of properly. See Remove the Front Seat Airbag and Discard for more information. Add Correction Code 20010707 to document the labor; the labor time for destructively removing and disposing of the front seat airbag and pretensioner is not reflected in the front seat removal and replacement labor time.
  • 2023-10-24: Updated gateway configuration value to be set when replacing a seat not equipped with a Farside Air Bag by a seat equipped with a Farside Air Bag.
  • 2023-07-19: Added seat track cover steps and updated software reinstall and seat calibrations steps.
  • 2023-06-19: Updated seat belt linkage release and install steps.
  • 2023-06-15: Added change config steps for replacing non-FSAB seat with FSAB-equipped seat.

Remove

  1. Open the LH doors and lower the LH windows.
  2. Move the 1st row LH seat forward.
  3. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  4. Remove the LH 1st row seat seat track rear covers.
  5. Remove and discard the bolts (x2) that attach the rear of the 1st row LH seat tracks to the floor panel.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  6. Move the 1st row LH seat rearwards.
  7. Remove the LH 1st row seat seat track front covers. See Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  8. Remove and discard the bolts (x2) that attach the front of the 1st row LH seat tracks to the floor panel.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  9. Move the seat to the middle of the track and the seat back to the most upright position.
  10. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Disconnect LV power. See LV Power (Disconnect and Connect).
  12. Lean the 1st row LH seat rearward to gain access to the underside of the seat.
  13. Release the clip that attaches the wiring harness to the seat assembly.
  14. Release the red locking tab on the black connector, and then disconnect the LH side body harness electrical connectors (x2) from the seat controller.
  15. With assistance, remove the 1st row LH seat from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution not to damage components during removal.

Install

  1. With assistance, position the 1st row LH seat into the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution not to damage components during installation.
  2. Lean the 1st row LH seat rearward to gain access to the underside of the seat.
  3. Connect the LH side body harness electrical connectors (x2) to the seat controller, and then engage the red locking tab on the black connector.
  4. Install the clip that attaches the wiring harness to the seat assembly.
  5. Connect LV power. See LV Power (Disconnect and Connect).
  6. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. Move the LH 1st row seat forward.
  8. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  9. Install new bolts (x2) that attach the rear of the 1st row LH seat tracks to the floor panel.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  10. Install the LH 1st row seat seat track rear covers.
  11. Move the driver seat rearward.
  12. Install new bolts (x2) that attach the front of the 1st row LH seat tracks to the floor panel.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  13. Install the LH 1st row seat seat track front covers. See Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  14. Move the driver seat to the original position.
  15. Locally connect a laptop with Toolbox 3 to the vehicle.
  16. North America only: If replacing a non-FSAB (Farside Air Bag) seat with an FSAB-equipped seat, perform the following:
    1. Use Toolbox 3 to change the configuration value for restraintsHardwareType to na_mxp2_fsab. See .
    2. Disconnect Toolbox 3 and remove the laptop from the vehicle.
  17. Use the vehicle touchscreen to enable Service Mode. See Service Mode (Enable and Disable).
  18. Reinstall the vehicle software. See Firmware Reinstall - Touchscreen.
  19. On the vehicle touchscreen, touch Driver Seat > Steering & Mirrors Calibration > Start, and then follow the on screen instructions.
  20. Close the LH doors and raise the LH windows.