16/09/2022 14:39:39

Insulator - Wheelhouse - Rear - RH (Remove and Replace)

Correction code 15307202 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open all the doors and open all the windows.
  2. Move the driver and front passenger seats fully forward.
  3. Remove the LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  4. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. Fold down the RH 2nd row seat back (40 portion).
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the seat from either button at the seat back or the from trunk switch.
  6. Remove the RH lower C-pillar trim. SeeTrim - C-Pillar - Lower - LH (Remove and Replace).
  7. Remove the RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  8. Release the clips (x3) that attach the RH lower C-pillar support bracket, and then remove the bracket from the vehicle.
  9. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  10. Disconnect LV power. See LV Power (Disconnect and Connect).
  11. Remove the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  12. Release the clips (x7) that attach the RH upper C-pillar trim, and then move the trim aside.
  13. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  14. Remove the rear wall rear trunk trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  15. Remove the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  16. Remove RH trunk load floor bracket. See Bracket - Trunk Load Floor - RH (Remove and Replace).
  17. Remove the RH trunk side trim. See Trim - Side - Trunk - RH (Remove and Replace).
  18. Remove the RH C-pillar support bracket. See Bracket - Support - C-Pillar - LH (Remove and Replace).
  19. Release the clips (x3) that attach the RH C-pillar mid and lower body bracket to the body.
  20. Remove the RH 2nd row seat back striker. See Striker - Seat Back - 2nd Row Seat - LH (Remove and Replace).
  21. Remove the closeout panel for the RH rear door latch assembly.
  22. Remove the bolts (x2) that attach the RH rear door latch to the body.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the RH rear door latch through the wheelhouse insulator, and then set the latch aside.
  23. Disconnect the electrical connector, then remove the nut that attaches the RH rear seatbelt retractor to the body, and then set the retractor aside.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
  24. Disconnect the LH taillight electrical connector.
  25. Remove the subwoofer. See Subwoofer (Remove and Replace).
  26. Remove the external audio amplifier. See Amplifier - Audio - External (Remove and Replace).
  27. Release the clips (x12) and bolt that attach the RH body harness to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  28. Remove the RH rear wheelhouse insulator.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully maneuver the insulator out of the vehicle.

Install

  1. Install the RH rear wheelhouse insulator.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully maneuver the insulator into the vehicle.
  2. Fasten the clips (x12) and bolt that attach the RH body harness to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the external audio amplifier. See Amplifier - Audio - External (Remove and Replace).
  4. Install the subwoofer. See Subwoofer (Remove and Replace).
  5. Connect the RH taillight electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the red locking tab.
  6. Install the RH C-pillar support bracket. See Bracket - Support - C-Pillar - LH (Remove and Replace).
  7. Connect the electrical connector, and then install the nut that attaches RH rear seatbelt retractor to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    15mm. Torque 40 Nm.
  8. Install the RH 2nd row seat back striker. See Striker - Seat Back - 2nd Row Seat - LH (Remove and Replace).
  9. Install the RH rear door latch through the wheelhouse insulator, and then install the bolts (x2) that attach the latch to the body.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  10. Fasten the clips (x3) that attach the RH C-pillar mid and lower body bracket to the body.
  11. Fasten the clips (x3) that attach the RH lower C-pillar support bracket to the body.
  12. Install the RH trunk side trim. See Trim - Side - Trunk - RH (Remove and Replace).
  13. Fasten the clips (x7) that attach the RH upper C-pillar trim to the body.
  14. Install the RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  15. Install the RH lower C-pillar trim. SeeTrim - C-Pillar - Lower - LH (Remove and Replace).
  16. Connect the 2nd row seat back electrical connector (40 portion).
  17. Raise the RH 2nd row seat back (40 portion) into the upright and locked position.
  18. Reconnect LV power. See LV Power (Disconnect and Connect).
  19. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  20. Install the rear wall rear trunk trim. See Trim - Rear Trunk - Rear Wall (Remove and Replace).
  21. Install the trunk floor front trim. See Trim - Front - Floor - Trunk (Remove and Replace).
  22. Install the RH trunk load floor bracket. See Bracket - Trunk Load Floor - RH (Remove and Replace).
  23. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  24. Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace).
  25. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  26. Install the LH and RH 2nd row seat outer bolsters. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace).
  27. Restore the driver and front passenger seats back to their original position.
  28. Raise all windows and close all doors.