17/06/2022 13:02:32

Fascia Assembly - Rear (HW3) (Remove and Replace)

Correction code 10013002 1.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the rear fascia assembly from the vehicle. See Fascia Assembly - Rear (Remove and Install).
  2. Pull the red tab to release the connector lock, and then disconnect the rear parking sensor electrical connectors (x6).
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  3. Pull the red tab to release the connector lock, and then disconnect the LH rear BLE assembly electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  4. Pull the red tab to release the connector lock, and then disconnect the RH rear BLE assembly electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  5. Release the clips (x8) and remove the adhesive pads (x4) that attach the wiring harness to the rear fascia assembly, and then remove the harness from the fascia assembly.
  6. Remove the parking sensors (x6) from the rear fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Sensors S7 and S12 (arrowed in image) are different from S8-S11 (circled in image).
  7. Remove the screws (x2) that attach the LH rear BLE assembly to the rear fascia, and then remove the assembly from the fascia. Repeat this step for the RH rear BLE assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 1. LH shown; RH similar
    Figure 2. LH shown; RH similar
  8. Remove the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    Figure 3. LH shown; RH similar
  9. Position the rear fascia assembly upside down on workbench.
  10. Remove the screws (x2) and release the tabs (x10) that attach the tow hitch cover to the rear fascia assembly, and then remove the cover from the assembly.
    Tip: Use of the following tool(s) is recommended:
    • Large flathead screwdriver
  11. Remove the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  12. Position the rear fascia assembly upright on the workbench.
  13. Release the tabs (x8) that attach the rear diffuser to the rear fascia assembly, and then remove the diffuser from the assembly.
  14. Remove the bolts (x2) that attach the rear lower fascia to the rear fascia assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  15. Release the tabs (x23) that attach the rear lower fascia to the rear fascia assembly, and then remove the lower fascia from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Insert a pick behind the lower fascia tab, and the rotate to pry the fascia assembly tab upward.
    Figure 4. LH shown RH similar

Install

  1. Place the new rear fascia assembly upside down on flat and protected surface.
  2. Position the rear lower fascia onto the rear fascia assembly, and then secure the tabs (x23) that attach the lower fascia to the assembly.
    Figure 5. LH shown; RH similar
  3. Place the rear fascia assembly upright on the workbench.
  4. Install the bolts that attach the rear lower fascia to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  5. Position the rear diffuser onto rear fascia assembly, and then secure the tabs (x8) that attach the diffuser to the fascia.
  6. Install the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    Figure 6. LH shown; RH similar
  7. Place the rear fascia assembly upside down on workbench.
  8. Install the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  9. Position the tow hitch cover onto the rear fascia assembly, and then secure the tabs (x10) that attach the cover to the fascia.
  10. Install the bolts that attach the tow hitch cover to the rear fascia.
    Tip: Use of the following tool(s) is recommended:
    • Large flathead screwdriver
  11. Place the rear fascia assembly upright on workbench.
  12. Position the RH rear BLE assembly onto the rear fascia, and then install the screws that attach the BLE assembly to the fascia. Repeat this step for the LH BLE assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Flex head ratchet/flex head torque wrench
    • 4 in extension
    Figure 7. LH shown; RH similar
  13. Install the parking sensors (x6) onto the rear fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Sensors S7 and S12 (arrowed in image) are different from S8-S11 (circled in image).
  14. Position the wiring harness onto the rear fascia assembly, and then install the clips (x8) and adhesive pads (x4) that attach the harness to the fascia.
  15. Connect the RH rear BLE assembly electrical connector, and then engage the connector lock. Repeat this step for the LH rear BLE assembly.
    Figure 8. LH shown; RH similar
  16. Connect the rear parking sensor electrical connectors (x6), and then engage the connector locks.
  17. Install the rear fascia assembly. See Fascia Assembly - Rear (Remove and Install).