11/07/2023 01:10:25

Assembly - Filter - HEPA (Remove and Replace)

Correction code 18105402 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-07-10: Corrected procedure title from Filter - HEPA (Remove and Replace) to Assembly - Filter - HEPA (Remove and Replace) and updated Correction Code and FRT.

Remove

  1. Move LH front seat backward.
  2. Remove LH front floor mat.
  3. Remove LH console side carpet.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  4. Release LH HEPA assembly lower dash bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 7Nm.
  5. Open RH front door.
  6. Lower RH front window.
  7. Move RH front seat backward.
  8. Remove RH front floor mat.
  9. Remove RH footwell cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connector.
  10. Remove RH mid A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs.
  11. Remove RH lower A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips.
  12. Remove RH console side carpet.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  13. Fold RH front cabin carpet aside for access.
  14. Release harness from RH footrest panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip.
  15. Remove RH footrest panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm.
  16. Release RH HEPA assembly lower dash bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 7Nm.
  17. Open hood.
    Informational PurposesAn informational icon, calling your attention
    Note
    Using center display touchscreen > Quick Controls > Frunk Open.
  18. Remove rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips.
  19. Remove LH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    10x clips.
  20. Remove RH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    10x clips.
  21. Release LH wiper arm hose nozzle.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose.
  22. Remove LH wiper arm nut cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cover.
  23. Remove LH wiper arm nut and release assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 15mm, 26 Nm, Do not flex wiper arm to remove, Lower the hood slightly to fit the tool.
  24. Release RH wiper arm hose nozzle.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose.
  25. Remove RH wiper arm nut cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cover.
  26. Remove RH wiper arm nut and release assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 15mm, 26 Nm.
  27. Release washer hose nozzle by LH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose, 3x clips.
  28. Remove LH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips, 1x fir tree clip.
  29. Remove RH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips, 1x fir tree clip.
  30. Remove wiper cowl screen panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x end tabs .
  31. Power off vehicle from center display.
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Safety & Security > Power Off.
  32. Disconnect LV battery connector and First Responder Loop.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection.
  33. Remove fasteners securing the LV battery and remove assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 9 Nm, 2x locators.
  34. Remove fasteners securing LH V-brace and remove assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm.
  35. Remove fasteners securing RH V-brace and remove assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm.
  36. Disconnect air quality sensor harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector.
  37. Remove HEPA filter assembly cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Maneuver cover forward and up in front of V-brace cross member.
  38. Remove HEPA filter.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Release clips, Pivot filter forward and out of housing.
  39. Release battery coolant pump from bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Slide pump off bracket and position lower coolant hose clear of HEPA assembly.
  40. Release V-brace crossmember.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, Torque?.
  41. Remove HEPA housing assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 7 Nm, Rotate V-brace cross member forward to create access to HEPA assembly retaining nuts, Maneuver assembly forward and up out of vehicle.

Install

  1. Install HEPA housing assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 7 Nm, Maneuver assembly down and under cross member, Rotate V-brace crossmember bracket back to install position.
  2. Secure V-brace crossmember.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, Torque?.
  3. Secure battery coolant pump to bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Slide pump on to bracket and secure lower coolant hose to bracket.
  4. Install HEPA filter.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x datums, 2x clips, Align 3 datums into bottom of housing, Confirm air flow direction, Ensure clips lock and secure filter into housing.
  5. Install HEPA filter assembly cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 2x datums, 2x slots, Maneuver cover down and under V-brace cross member, Fully engage seal and locking tabs.
  6. Connect air quality sensor harness.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector.
  7. Install fasteners securing RH V-brace and secure.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm.
  8. Install fasteners securing LH V-brace and secure.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm.
  9. Install wiper cowl screen panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x end tabs.
  10. Install LV battery to multi-system beam.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 9 Nm, 2x locators.
  11. Connect First Responder Loop and LV battery connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
  12. Using center display, remove wipers from "Service Mode".
  13. Install RH wiper arm assembly and secure nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 15mm, 26 Nm, Line up wiper to reference mark on windshield.
  14. Install RH wiper arm nut cover.
  15. Secure RH wiper arm washer nozzle.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose, Hose is routed below the arm.
  16. Install LH wiper arm assembly and secure nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 15mm, 26 Nm, Line up wiper to reference mark on windshield.
  17. Install LH wiper arm nut cover.
  18. Secure LH wiper arm washer nozzle.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose, Hose is routed below the arm.
  19. Install RH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clip, 1x fir tree clip.
  20. Install LH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clip, 1x fir tree clip.
  21. Secure washer hose nozzle by LH shock tower cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose, 3x clips.
  22. Install RH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    10x clips.
  23. Install LH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    10x clips.
  24. Install rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips.
  25. Close hood .
    Informational PurposesAn informational icon, calling your attention
    Note
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood.
  26. Secure RH HEPA assembly lower dash bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 7Nm.
  27. Install RH footrest panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm.
  28. Secure harness to RH footrest panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip.
  29. Fold RH main carpet back into place.
  30. Install RH mid A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs, Verify weather seal is seated properly.
  31. Install RH lower A-pillar trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Verify weather seal is seated properly.
  32. Install RH console side carpet.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  33. Install RH footwell cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connectors.
  34. Install RH front floor mat.
  35. Move RH front seat to original position.
  36. Raise RH front window.
  37. Close RH front door.
  38. Secure LH HEPA assembly lower dash bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 7Nm.
  39. Install LH console side carpet.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  40. Install LH front floor mat.
  41. Move LH front seat to original position.