01/12/2022 14:27:37

Pipe Assembly - ABS to LH Sill Pipes (Remove and Replace)

Correction code 33031702 2.46 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door.
  2. Lower the LH front window.
  3. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  4. Remove all four wheels. See Wheel Assembly (Remove and Install).
  5. Lower vehicle partially and set lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise the lift off locks, and then hold lock release lever to keep locks free while vehicle is lowered. Set vehicle to comfortable working height.
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. On the touchscreen, touch Controls > Safety & Security > Power Off.
  8. Disconnect LV power. See LV Power (Disconnect and Connect).
  9. Remove the LH and RH underhood aprons. See Underhood Apron - LH (Remove and Replace).
  10. Remove the LH and RH wiper arms. See Wiper Arm - LH (Remove and Replace).
  11. Remove the LH and RH shock tower covers. See Cover - Shock Tower - LH (Remove and Replace).
  12. Remove the cowl screen panel. See Panel - Cowl Screen (Remove and Replace).
  13. Remove the bolts (x3) that attach the LV battery to the vehicle, and then move the battery aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of datums (x2) and carefully move battery aside.
    Tip: Use of the following tool(s) is recommended:
    • 4 in extension
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratcheting combination wrench flex head 10 mm
  14. Remove the LH shock tower V brace. See V Brace - Shock Tower - LH (Remove and Replace).
  15. Clean the area around the brake fluid reservoir, and then remove the brake reservoir cap.
  16. Remove brake fluid from the brake reservoir.
    Tip: Use of the following tool(s) is recommended:
    • Oil catch/measure kit - 1541474-00-B
  17. Install the brake reservoir cap.
  18. Disconnect the air quality sensor harness connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  19. Release the tabs (x2) that attach the HEPA filter assembly cover to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be cautious and do not damage the mounting clips. Maneuver the cover forward and upwards in front of the V-brace cross member.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  20. Remove the battery controller module. See Module - Battery Controller (Remove and Replace).
  21. Remove the LH front wheel arch liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  22. Remove the brake hydraulic control unit. See Hydraulic Control Unit (HCU) - Brake (Remove and Replace).
  23. Place shop rags underneath the ABS to LH sill pipes pipe assembly junction block to catch any fluid lost.
  24. Remove the nuts (x2) that attach the ABS to LH sill pipes pipe assembly to the LH brake pipe junction block.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow brake fluid to drain as pipes are removed. Catch fluid with shop towels as needed.
    Tip: Use of the following tool(s) is recommended:
    • Ratcheting combination wrench flex head 12mm
  25. Remove the ABS to LH sill pipes pipe assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the sill pipe assembly over the front pipe assembly and through the body opening.

Install

  1. Position the ABS to LH sill pipes pipe assembly on the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the sill pipe assembly through body opening and over front pipe assembly.
  2. Install the nuts (x2) that attach the ABS to LH sill pipes pipe assembly to the LH brake pipe junction block.
    16 Nm (11.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • 3/8 in open crowfoot socket 12mm
    • Ratcheting combination wrench flex head 12mm
    • Ratchet/torque wrench
  3. Remove the shop rags from underneath the ABS to LH sill pipes pipe assembly junction block.
  4. Install the brake hydraulic control unit. See Hydraulic Control Unit (HCU) - Brake (Remove and Replace).
  5. Install the LH front wheel arch liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  6. Install the battery controller module. See Module - Battery Controller (Remove and Replace).
  7. Install the tabs (x2) that attach the HEPA filter assembly cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Maneuver the cover downward and under the V-brace cross member. Fully engage the seal and locking tabs.
  8. Connect the air quality sensor harness connector.
  9. Install the LH shock tower V brace. See V Brace - Shock Tower - LH (Remove and Replace).
  10. Install the cowl screen panel. See Panel - Cowl Screen (Remove and Replace).
  11. Install the bolts (x3) that attach the LV battery to the vehicle.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 4 in extension
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratcheting combination wrench flex head 10 mm
    • Ratchet/torque wrench
  12. Install the LH and RH wiper arms. See Wiper Arm - LH (Remove and Replace).
  13. Install the LH and RH shock tower covers. See Cover - Shock Tower - LH (Remove and Replace).
  14. Connect LV power. See LV Power (Disconnect and Connect).
  15. Clean the area around the brake fluid reservoir, and then remove brake reservoir cap.
  16. Perform a brake fluid flush. Brake Fluid Bleed/Flush (Remove and Replace).
  17. Install the LH and RH underhood aprons. See Underhood Apron - LH (Remove and Replace).
  18. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  19. Raise the vehicle partially and lower onto locks.
    Informational PurposesAn informational icon, calling your attention
    Note
    Set the vehicle to a comfortable working height. Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
  20. Install all four wheels. See Wheel Assembly (Remove and Install).
  21. Lower the vehicle. See Raise Vehicle - 2 Post Lift.
  22. Raise the LH front window.
  23. Close the LH front door.
  24. Perform a post-repair validation test drive and ensure proper brake pedal feel and performance.
    Important: Add correction code 00040100 to account for time.