15/08/2023 10:15:58

Antenna - Satellite Radio (Remove and Replace)

Correction code 21311002 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.
  1. Open LH front door
  2. Lower LH front window
  3. Remove LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs
  4. Remove LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  5. Remove LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tethered clips, 1x clip, 1x connector, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove each tether from body side, Disconnect tweeter, Then pull upper A-pillar upward to remove
  6. Remove LH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Extending the sun visor may allow for extra working room
  7. Remove LH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  8. Remove LH sun visor from headliner area
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold sun visor to the closed and folded down position but do not latch in place
  9. Disconnect LH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  10. Open RH front door
  11. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs
  12. Remove RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  13. Remove RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tethered clips, 1x clip, 1x connector, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove each tether from body side, Disconnect tweeter, Then pull upper A-pillar upward to remove
  14. Remove RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Extending the sun visor may allow for extra working room
  15. Remove RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  16. Remove RH sun visor from headliner area
  17. Disconnect RH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  18. Release rear view mirror lower cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x tabs, Press inward on the sides of the cover and pull the bottom edge downward to release
  19. Disconnect rear view mirror connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  20. Remove rear view mirror
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate mirror to release
  21. Remove upper rear view mirror cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 3x connectors, Carefully pull down on upper rear view mirror cover to release from clips
  22. Move LH front seat forward
  23. Open LH rear door
  24. Release LH front seat belt
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn release mechanism counter clockwise, turn back clockwise after releasing
  25. Partially release LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Release from upper trim and body
  26. Remove LH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Release clips and route seatbelt through B-pillar, Be cautious not to separate the upper B-pillar, There are plastic welds near the center of trim holding upper and lower portion together
  27. Push open LH coat hook
  28. Pry open LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  29. Remove LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 2.5 Nm
  30. Move RH front seat forward
  31. Open RH rear door
  32. Release RH front seat belt
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn release mechanism counter clockwise, turn back clockwise after releasing
  33. Partially release RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Release from upper trim and body
  34. Remove RH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Release clips and route seatbelt through B-pillar, Be cautious not to separate the upper B-pillar, There are plastic welds near the center of trim holding upper and lower portion together
  35. Push open RH coat hook
  36. Pry open RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  37. Remove RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 2.5 Nm
  38. Open liftgate
  39. Remove parcel shelf
  40. Remove LH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Start by releasing upper portion
  41. Fold the 60 seat in down position
    Informational PurposesAn informational icon, calling your attention
    Note
    Release seat from either button at backrest or from trunk switch, If seat cushion is not present, protect the seat as required
  42. Separate LH lower C-pillar trim from LH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  43. Remove LH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  44. Release LH upper C-pillar trim and move aside
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  45. Remove RH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Start by releasing upper portion
  46. Fold the 40 seat in down position
    Informational PurposesAn informational icon, calling your attention
    Note
    If seat cushion is not present, protect the seat as required
  47. Separate RH lower C-pillar trim from RH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x datum
  48. Remove RH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  49. Release RH upper C-pillar trim and move aside
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  50. Remove bolts securing rear of headliner to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 3 Nm, Bolt located on LH & RH side of headliner
  51. Release headliner from body
    Informational PurposesAn informational icon, calling your attention
    Note
    18x clips, 2x hooks, Headliner will be supported by 8x tethers when released, Push upward and inward to release hooks on the coat hook assemblies from the body
  52. Close liftgate
  53. Apply tape to the vehicle exterior
    Informational PurposesAn informational icon, calling your attention
    Note
    Cover the side rails and front corners of the liftgate
  54. Measure and record gaps from fixed roof glass to windshield, body sides, and liftgate glass
    Informational PurposesAn informational icon, calling your attention
    Note
    Measurements will be used during installation of new glass
  55. Open liftgate
  56. Apply masking tape to protect the headliner
  57. Cut length of square wire to use with T-handles
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure there's adequate wire
  58. Insert tool through roof glass urethane at rear corner
  59. Attach square wire and pull tool back through into vehicle
  60. Insert square wire into one T-handle
  61. Attach second T-handle
  62. Using T-handles, cut urethane securing roof glass to body
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Use caution near XM antenna, roof rack blocks, and bolts for brackets near B-pillars
  63. Secure suction cups to roof glass at each corner
    Informational PurposesAn informational icon, calling your attention
    Note
    4x suction cup tools, Recommend assistance
  64. Remove fixed roof glass from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, discard per local regulations
  65. Remove old urethane from body
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure residual urethane is 1 mm or less in thickness
  66. Remove datums and any other debris from body
  67. Wipe body with IPA to clean surface
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow 1 minute dry time
  68. Replace any body plugs or tape that were damaged during removal or cleaning
  69. Inspect XM antenna to make sure it is secure and the foam is not damaged
    Informational PurposesAn informational icon, calling your attention
    Note
    If damaged, please replace as needed.
  70. Disconnect XM antenna harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  71. Release XM antenna harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x harness clips
  72. Remove XM antenna from body
    Informational PurposesAn informational icon, calling your attention
    Note
    4x pieces double sided tape
  73. Remove residual double sided tape from the body
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow 1 minute dry time
  74. Release tether clips from body
    Informational PurposesAn informational icon, calling your attention
    Note
    6x tether clips, This will assist with headliner installation later, A good tool to release these clips is available for purchase via eProcurment in the Grainger punchout catalog, Item #2ZPP2 - GearWrench Push Pin Pliers
  75. Install XM antenna to body
    Informational PurposesAn informational icon, calling your attention
    Note
    4x pieces double sided tape
  76. Install XM antenna harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x harness clips
  77. Connect XM antenna harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  78. Attach suction cups to new roof glass
  79. Position new roof glass onto vehicle for dry fit
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  80. Make sure gaps are all within acceptable limits
    Informational PurposesAn informational icon, calling your attention
    Note
    If glass is too high, it may be necessary to trim or remove net pads
  81. Remove roof glass and set it upside-down onto stand
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  82. Remove protective tape from vehicle body
  83. Clean glass mating surfaces with isopropyl alcohol
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow 1 minute dry time
  84. Apply primer to body on urethane path and any areas that were damaged during removal
    Informational PurposesAn informational icon, calling your attention
    Note
    If vehicle is equipped with roof rack anchors, primer should go around the inside of the roof bracket. If vehicle is not equipped with roof rack brackets, primer outside the roof rack bracket mounting holes. Allow primer to dry for at least 1 minute
  85. Prepare caulking gun and urethane
    Informational PurposesAn informational icon, calling your attention
    Note
    Opening must be 8mm wide and 14mm tall
  86. Apply urethane to body
    Informational PurposesAn informational icon, calling your attention
    Note
    If equipped with roof rack anchors urethane should go around the inside of the roof rack anchor, if not urethane should go on the outside of the anchor mounting holes.
  87. Place new roof glass onto vehicle but do not set yet
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance. Align datum at rear of glass to body
  88. Position new seal at front of glass beneath windshield seal
    Informational PurposesAn informational icon, calling your attention
    Note
    A trim tool can be used to properly seat the roof glass seal under the windshield seal
  89. Press glass onto body once in position
    Informational PurposesAn informational icon, calling your attention
    Note
    Use sandbags for the front if needed
  90. Verify clearances with liftgate glass, windshield, and body sides are within CVIS specification
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust if necessary
  91. Remove suction cups from roof glass
  92. Remove protective tape from headliner
  93. Secure tether clips to headliner
    Informational PurposesAn informational icon, calling your attention
    Note
    Listen for audible click when seated properly
  94. Secure headliner to body
    Informational PurposesAn informational icon, calling your attention
    Note
    18x clips, 2x hooks, Push coat hook upward and outward to secure hooks to the body flange at the top of the coat hook assembly
  95. Install bolts securing rear of headliner to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 3 Nm, Bolt located on LH & RH side of headliner
  96. Install RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Replace any damaged clips
  97. Install RH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Replace any damaged clips
  98. Secure RH lower C-pillar trim onto RH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  99. Fold the 40 seat into vertical position
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove seat cushion protection
  100. Install RH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top
  101. Install LH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Replace any damaged clips
  102. Install LH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, Replace any damaged clips
  103. Secure LH lower C-pillar trim onto LH mid C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  104. Fold the 60 seat into vertical position
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove seat cushion protection
  105. Install LH side bolster trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top
  106. Install parcel shelf
  107. Close liftgate
  108. Install RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 2.5 Nm
  109. Close RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  110. Push RH coat hook closed
  111. Install LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 2.5 Nm
  112. Close LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  113. Push LH coat hook closed
  114. Install RH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Route seatbelt through B-pillar, Replace any damaged or missing clips
  115. Reinstall top portion of RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Replace any damaged or missing clips
  116. Secure RH front seat belt
  117. Move RH front seat to original position
  118. Close RH rear door
  119. Install LH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Route seatbelt through B-pillar, Replace any damaged or missing clips
  120. Reinstall top portion of LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Replace any damaged or missing clips
  121. Secure LH front seat belt
  122. Close LH rear door
  123. Move LH front seat to original position
  124. Install upper rear view mirror cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 3x connectors, Ensure the rear view mirror harness is routed so that it hangs freely on the outside and is not pinched between the cover and glare shield assembly
  125. Install rear view mirror
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the rear view mirror by turning mirror counter clockwise until mirror is secured
  126. Connect rear view mirror connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Connect rear view mirror connector and tuck harness slack along the arm
  127. Connect RH sunvisor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  128. Install RH sun visor into headliner area
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold sun visor to the closed and folded down position, but do not latch in place
  129. Install RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3.5 Nm
  130. Install RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  131. Install RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tethered clips, 1x clip, 1x connector, Slide bottom of trim along IP and speaker grill, attach each tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  132. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  133. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs, Verify weather seal is seated properly
  134. Close RH front door
  135. Connect LH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  136. Install LH sun visor into headliner area
  137. Install LH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3.5 Nm
  138. Install LH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  139. Install LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tethered clips, 1x clip, 1x connector, Slide bottom of trim along IP and speaker grill, attach each tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  140. Install LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  141. Install LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 2x tabs, Verify weather seal is seated properly
  142. Install tether onto rear view mirror lower cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Guide tabs through anchor on rear view mirror lower cover
  143. Install rear view mirror lower cover
    Informational PurposesAn informational icon, calling your attention
    Note
    4x tabs, Install the tabs closest to the rearview mirror assembly and push the cover up to secure
  144. Raise LH front window
  145. Close LH front door