2023-01-20

Shield - Dust - Brake - Rear - LH (Remove and Replace)

Correction code 33011802 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift
  2. Release the parking brake caliper. See Park Brake Caliper - Release.
  3. Remove the LH rear wheel center cap.
  4. Loosen the LH rear axle nut.
  5. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  6. Remove the axle nut and discard the washer that attach the LH rear drive axle to the hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    If washers are not present, procure a set so they can be installed later in this procedure.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32 mm deep impact socket
  7. If installed, remove and discard the bolt that attaches the brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    A new bolt will not be installed.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  8. Install the hub puller to the LH rear brake rotor.
  9. Use the hub puller to release the LH rear halfshaft from the hub splines.
  10. Remove the hub puller from the LH rear hub assembly.
  11. Remove the LH rear rotor. See Brake Rotors - Rear - Set (Remove and Replace).
  12. Remove the LH rear hub. See Hub - Rear - LH (Remove and Replace).
  13. Remove the bolts (x3) that attach the LH rear brake dust shield to the vehicle.

Install

  1. Install the bolts (x3) that attach the LH rear brake shield to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    T30, 8 Nm
  2. Install the LH rear hub. See Hub - Rear - LH (Remove and Replace).
  3. Install the LH rear brake rotor. See Brake Rotors - Rear - Set (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not install the a bolt to attach the brake rotor to the hub.
  4. Install the axle nut and new washer hand tight.
    Informational PurposesAn informational icon, calling your attention
    Note
    The axle nut will be torqued at a later step.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32 mm deep impact socket
  5. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  6. Lower the vehicle until the tires are touching the ground.
  7. Torque the axle nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    32mm, 245 Nm
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32 mm deep impact socket
  8. Install the LH rear wheel cap, aligning the valve stem with the wheel cap.
  9. Touch and hold the 'Park' on the vehicle display to release EPB service mode.