17/06/2022 13:23:55

HV Header - Rear Drive Unit - HV Battery - LH (Remove and Replace)

Correction code 16306312 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Raise and support vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Set air suspension to "Jack Mode".
  2. Open hood.
    Informational PurposesAn informational icon, calling your attention
    Note
    Using center display touchscreen > Quick Controls > Frunk Open.
  3. Remove rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips.
  4. Power off vehicle from center display.
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Safety & Security > Power Off.
  5. Disconnect LV battery connector and First Responder Loop.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection.
  6. Verify operation of multimeter.
    Informational PurposesAn informational icon, calling your attention
    Note
    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing LV battery, Touch lightly and do not damage terminals.
  7. Raise vehicle fully and lower lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Note
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
  8. Remove clips securing mid aero shield.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips.
  9. Remove bolts securing mid aero shield and remove from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    16x bolts, 10mm, 6 Nm.
  10. Remove all items from pockets and ensure not wearing metal items.
  11. Inspect HV insulating gloves.
    Informational PurposesAn informational icon, calling your attention
    Note
    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.
  12. Put on HV insulating gloves and leather over gloves.
  13. Release LH RDU HV harness from HV battery.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Hold down red locking tab and disengage the release lever, Do not force the release lever up.
  14. Verify no high voltage at LH rear RDU HV header.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering.
  15. Remove bolts securing HV pack RDU header.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10 EPRL, 10 Nm.
  16. Remove HV pack RDU header.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Gently remove header from battery pack.

Install

  1. Secure HV pack RDU header.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Verify it is fully seated.
  2. Install bolts securing HV pack RDU header.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10 EPRL, 10 Nm, Tight down evenly.
  3. Secure LH RDU HV harness to battery pack.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins.
  4. Remove the leather glove protectors and HV insulating gloves.
  5. Remove gore breathers from rear breather assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x breathers, Breathers are to be re-used, Be cautious during removal and do not incur damage, If damaged proceed to replacement, Located at rear of pack.
  6. Secure tapered plugs into the three indicated breather holes.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x tapered plugs, Do not push plugs too far inside.
  7. Secure the leak test adapter onto the fourth breather hole.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x leak test adapter.
  8. Close both valves on the regulator test tool.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify valves are closed.
  9. Secure enclosure leak tester fitting to the leak test adapter.
    Informational PurposesAn informational icon, calling your attention
    Note
    If required, safely secure the leak tester air line in a manner where it will not tug the adapter off.
  10. Connect regulator to air supply.
  11. Turn right side regulator valve to the open position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Open valve closest to the air line, By turning the valve knob to a horizontal position, The valve is fully open.
  12. Set regulator to 0.3 psi.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow regulator to stablize.
  13. Open the left side regulator valve to allow air into the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Note
    Close right side regulator valve when the pressure reaches 0.3 psi and stabilizes, It will take roughly 60 seconds to reach 0.3 psi.
  14. Wait 60 seconds to allow pressure to stabilize.
  15. Record start pressure value.
  16. Wait 30 seconds for test.
  17. Record end pressure value.
    Informational PurposesAn informational icon, calling your attention
    Note
    If pressure did not drop more than 0.026 psi, continue to next step, If pressure dropped more than 0.026 psi, then inspect HV battery enclosure for leaks.
  18. Disconnect air supply from leak tester.
  19. Release enclosure leak tester fitting from the leak test adapter.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the leak tester air line if previously secured.
  20. Release leak test adapter from breather hole.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x leak test adapter.
  21. Release tapered plugs from the breather holes.
    Informational PurposesAn informational icon, calling your attention
    Note
    3x tapered plugs.
  22. Secure gore breathers onto rear breather assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x gore breathers, If breathers were damaged replace as required.
  23. Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    16x bolts, 10mm, 6 Nm.
  24. Install clips securing mid aero shield.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips.
  25. Lower vehicle fully.
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  26. Connect First Responder Loop and LV battery connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
  27. Install rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips.
  28. Close hood .
    Informational PurposesAn informational icon, calling your attention
    Note
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood.
  29. Remove vehicle from lift.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode".