2024-12-24

Steering Wheel Switch Bezel Surround (Remove and Replace)

Correction code 3205011102 FRT 0.35 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: STEERING WHEEL SWITCH - LEFT HAND (Remove and Install) and Steering Wheel Switch Bezel Surround (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x4) that attach the steering wheel lower trim to the steering wheel
1.4 Nm (1.0 lbs-ft)
  • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
Reuse
Screws (x2) that attach the steering wheel housing to the steering wheel
1.4 Nm (1.0 lbs-ft)
  • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
Reuse
Screws (x4) that attach the steering wheel housing to the steering wheel
1.8 Nm (1.3 lbs-ft)
  • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
Reuse
Screws that attach the steering wheel switch to the steering wheel.
0.8 Nm (7 lbs-in)
  • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
Reuse

Remove

  1. Remove the steering wheel. See STEERING WHEEL (Remove and Install).
  2. Remove the steering wheel horn. See Steering Wheel - Horn (Remove and Replace).
  3. Release the tabs (x6) that attach the cover plate to the steering wheel.
  4. Remove the screws (x4) and tabs (x2) that attach the steering wheel lower trim to the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  5. Remove the screws (x2) that attach the steering wheel housing to the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  6. Remove the screws (x4) that attach the steering wheel housing to the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  7. Release the tabs (x5) that attach the steering wheel housing to the steering wheel.
  8. Release the tabs (x4) that attach the steering wheel upper housing to the steering wheel.
  9. Remove the screws (x8) that attach the LH and RH steering wheel switches to the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
    Figure 1. LH shown, RH similar
  10. Remove the steering wheel switch bezel from the vehicle.

Install

  1. Install the steering wheel switch bezel to the vehicle.
  2. Install the screws (x8) that attach the LH and RH steering wheel switches to the steering wheel.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  3. Install the tabs (x4) that attach the steering wheel upper housing to the steering wheel.
  4. Install the tabs (x5) that attach the steering wheel housing to the steering wheel.
  5. Install the screws (x4) that attach the steering wheel housing to the steering wheel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  6. Install the screws (x2) that attach the steering wheel housing to the steering wheel.
    1.4 Nm (1.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  7. Install the screws (x4) and tabs (x2) that attach the steering wheel lower trim to the steering wheel.
    1.4 Nm (1.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 1450424-00-A - SET, 1/2" CUT BIT. (78 PCS DOUBLE END MINI RATCHET)
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  8. Install the tabs (x6) that attach the cover plate to the steering wheel.
  9. Install the steering wheel horn. See Steering Wheel - Horn (Remove and Replace).
  10. Install the steering wheel. See STEERING WHEEL (Remove and Install).