16/10/2024 01:09:40

Camera - Forward Facing (Pitch Verification)

Correction code 17221000 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 1448868-00-A Wrench, 2.5mm, Thin
Informational PurposesAn informational icon, calling your attention
Note
This procedure was designed for vehicles with factory suspension components. Check if the vehicle has modified suspension components, as this might affect whether calibration can be completed.
  • 2023-08-07: Updated the procedure.
  • 2023-07-18: Added steps to set the ride height and enable Jack Mode.
  • 2023-06-19: Updated images and added notes to check measurements before each setup.
  • 2023-06-08: Added specifications for HW4 and general image and step updates.

Setup

  1. Park the vehicle on a flat surface with at least 106 cm (3.5 ft) of space in front of the front fascia.
  2. Set the vehicle ride height to "Medium" and then enable Jack Mode.
  3. Set up the target so that the bottom of the rectangle is 90 cm (3 ft) from the ground.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not assume the tripod is at the correct height from previous verifications. The tripod may have shifted when moved. Measure the height before each setup.
  4. Place the target in the appropriate starting position:
    • The checkered portion of the target is facing towards the vehicle.
    • The target is centered with the Tesla "T" on the hood.
    • The target is placed as close to the front fascia as possible.
  5. Make sure that the target is on flat ground by examining the bubble level on the back of the target.
  6. Apply a piece of red tape on the target so that the top of the tape is 149 cm (58.6 in) from the ground.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not use existing marks from previous verifications. Remove any existing tape. Measure and reapply new tape to ensure the tape is in the correct location.
    Informational PurposesAn informational icon, calling your attention
    Note
    The checker pattern on the target is used for vehicles with 1st generation Autopilot. Ignore the checker pattern when affixing the tape.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the vehicle is equipped with aftermarket suspension components that alter the vehicle ride height, the red tape might have to be adjusted to ensure accurate pitch verification.
  7. For HW4 vehicles on firmware version develop/2023.26.X or factory/2023.20.200 or later AND non HW4 vehicles on firmware version develop/2023.20.X or later, continue to Adjust (Service Mode). For HW3 and HW4 vehicles on firmware versions older than the versions mentioned above, continue to Adjust (Toolbox 3).

Adjust (Service Mode)

  1. Enable Service Mode through the touchscreen. See Service Mode (Enable and Disable).
  2. Unlock the vehicle gateway for diagnostic communication. See Gateway (Unlock).
  3. Touch Driver Assist (steering wheel icon) and then touch Cameras.
  4. Touch Clear Camera Calibration, select ForwardFacing, and then touch Run.
  5. Touch Close when the routine has passed.
  6. Touch Reset DAS, and then touch Run.
  7. Touch Close when the routine has passed.
  8. Touch Camera Preview and then touch Main.
  9. Touch Pitch Verification to add the verification lines on the display.
  10. Review the image on the touchscreen:
    Informational PurposesAn informational icon, calling your attention
    Note
    The top of the red tape (A) should coincide with the blue horizontal line. However, if the top of the red tape is between the green lines, that is sufficient.
    • If the top of the red tape (A) is between the two green lines (B and C), the forward facing camera is within calibration. Go to step 17.
    • If the top of the red tape (A) is not between the two green lines (B and C), the forward facing camera needs adjustment. Continue to the next step to adjust the camera.
    Figure 1. HW3
    Figure 2. HW4
  11. HW3 only: Repeat steps 8 through 10 for Narrow camera.
  12. Remove the rear view mirror. See Mirror - Rear View (Remove and Replace).
  13. Remove the upper camera cover assembly to access the camera pitch adjustment. See Upper Cover - Rear View Mirror (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove any components from the cover assembly.
  14. Use a pitch adjustment wrench to adjust the camera pitch so that the top of the red tape coincides with the horizontal blue line.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotating the wrench clockwise pitches the camera up, and counterclockwise pitches the camera down conversely. 1 full rotation of the wrench can adjust the pitch 0.5 - 1.5 degrees.
    Tip: Use of the following tool is recommended:
    • Pitch adjustment wrench - 1448868-00-B
  15. Install the upper camera cover assembly. See Upper Cover - Rear View Mirror (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove any components from the cover assembly.
  16. Install the rear view mirror. See Mirror - Rear View (Remove and Replace).
  17. Touch Controls (vehicle icon), Service Mode and then touch Exit Service Mode.
  18. Remove the target from the front of the vehicle.
  19. Disable Jack Mode.
  20. The vehicle needs to be driven by the customer to complete the calibration procedure.
    Informational PurposesAn informational icon, calling your attention
    Note
    Self-calibration can take up to 100 miles (160 km) of manual driving, depending upon the road type and condition. Until self-calibration is complete, the message "Autopilot Features Currently Unavailable: Manual Driving Required While Camera Is Calibrating" is displayed if an attempt is made to engage an Autopilot feature.

Adjust (Toolbox 3)

Informational PurposesAn informational icon, calling your attention
Note
Adjustment of the forward facing camera is an iterative process. That is, check the narrow and main images, adjust accordingly, check the narrow and main images, adjust accordingly, etc.
Informational PurposesAn informational icon, calling your attention
Note
The actions of entering the vehicle, inserting the wrench, turning the wrench, and then exiting the vehicle affect the camera alignment during those actions, therefore you cannot adjust the camera in real time.
  1. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  2. Exit the vehicle and select Dashboards > DAS Tools > Display DAS Images > Clear Calibration and Capture Image.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Freeze-frame narrow and main images are captured, and the vehicle needs to be unoccupied at this time in order for the ride height to maintain specification
  3. Review the freeze-frame main image:
    Informational PurposesAn informational icon, calling your attention
    Note
    The top of the red tape (A) should coincide with the blue horizontal line.
    • If the top of the red tape (A) is not coinciding with the blue horizontal line, the forward facing camera needs adjustment. Continue to the next step to adjust the camera.
  4. Remove the rear view mirror. See Mirror - Rear View (Remove and Replace).
  5. Remove the upper camera cover assembly to access the camera pitch adjustment. See Upper Cover - Rear View Mirror (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove any components from the cover assembly.
  6. Use a pitch adjustment wrench to adjust the camera pitch so that the top of the red tape coincides with the horizontal blue line.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotating the wrench clockwise pitches the camera up, and counterclockwise pitches the camera down conversely. 1 full rotation of the wrench can adjust the pitch 0.5 - 1.5 degrees.
    Tip: Use of the following tool is recommended:
    • Pitch adjustment wrench - 1448868-00-B
  7. Exit the vehicle, and in Toolbox, select Capture Image to capture updated freeze-frame narrow and main images.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the vehicle remains unoccupied as the image capture is performed.
  8. Repeat the procedure from step 3.
  9. Install the upper camera cover assembly. See Upper Cover - Rear View Mirror (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove any components from the cover assembly.
  10. Install the rear view mirror. See Mirror - Rear View (Remove and Replace).
  11. Disconnect the laptop from the vehicle.
  12. Remove the target from the front of the vehicle.
  13. Disable Jack Mode.
  14. The vehicle needs to be driven by the customer to complete the calibration procedure.
    Informational PurposesAn informational icon, calling your attention
    Note
    Self-calibration can take up to 100 miles (160 km) of manual driving, depending upon the road type and condition. Until self-calibration is complete, the message "Autopilot Features Currently Unavailable: Manual Driving Required While Camera Is Calibrating" is displayed if an attempt is made to engage an Autopilot feature.